|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
External Network Adapter for Solaris 10
Post 302355151 by DukeNuke2 on Monday 21st of September 2009 05:54:59 PM
09-21-2009
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so? (1 Reply)
Discussion started by: ghuber
1 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
5. IP Networking
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
Discussion started by: wilsonSurya
3 Replies
6. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
7. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
8. Solaris
Hello all, thanks for reading my question:
So I've been a Unix/Linux SysAdmin for a couple years, and I'm a bit over my head running solo, trying to set up LDoms using Oracle VM Server 3.1 for SPARC. I've been very careful, and things have gone well up until the point I try to access the new... (9 Replies)
Discussion started by: Lyxix
9 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT OPENDARWIN
bwi
BWI(4) BSD Kernel Interfaces Manual BWI(4) NAME
bwi -- Broadcom BCM43xx IEEE 802.11b/g wireless network driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device bwi device wlan device wlan_amrr device firmware Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_bwi_load="YES" DESCRIPTION
The bwi driver provides support for Broadcom BCM43xx based PCI/CardBus network adapters. It supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on configur- ing this device, see ifconfig(8). This driver requires firmware to be loaded before it will work. The ports/net/bwi-firmware-kmod port needs to be installed before ifconfig(8) will work. HARDWARE
The bwi driver supports Broadcom BCM43xx based wireless devices, including: Card Chip Bus Standard Apple Airport Extreme BCM4306 PCI b/g Apple Airport Extreme BCM4318 PCI b/g ASUS WL-138g BCM4318 PCI b/g Buffalo WLI-CB-G54S BCM4318 CardBus b/g Buffalo WLI-PCI-G54S BCM4306 PCI b/g Compaq R4035 onboard BCM4306 PCI b/g Dell Wireless 1470 BCM4318 Mini PCI b/g Dell Truemobile 1400 BCM4309 Mini PCI b/g HP nx6125 BCM4319 PCI b/g Linksys WPC54G Ver 3 BCM4318 CardBus b/g Linksys WPC54GS Ver 2 BCM4318 CardBus b/g TRENDnet TEW-401PCplus BCM4306 CardBus b/g US Robotics 5411 BCM4318 CardBus b/g EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev bwi0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev bwi0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev bwi0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up SEE ALSO
arp(4), cardbus(4), intro(4), pci(4), wlan(4), wlan_amrr(4), ifconfig(8), wpa_supplicant(8) HISTORY
The bwi driver first appeared in FreeBSD 8.0. AUTHORS
The bwi driver was written for DragonFly BSD by Sepherosa Ziehau and subsequently ported to FreeBSD. BUGS
Some card based on the BCM4306 and BCM4309 chips do not work properly on channel 1, 2 and 3. BSD
May 16, 2009 BSD