Hi all,
We are facing the following problem in our HP-UX machine: software that manipulates utf-8 encoded strings (e.g. during string cut), fails to correctly manipulate strings (all containing Greek characters) that contain special characters like @, &, # etc. Actually, in different... (3 Replies)
When I open a file in vi, I see the following characters:
\302\240
Can someone explain what these characters mean. Is it ASCII format? I need to trim those characters from a file.
I am doing the following:
tr -d '\302\240'
---------- Post updated at 08:35 PM ---------- Previous... (1 Reply)
Hi all,
I was wondering how can i see the special characters like \t, \n or anything else in a file by using Nano or any other linux command like less, more etc (6 Replies)
i need to replace the any special characters with escape characters like below.
test!=123-> test\!\=123
!@#$%^&*()-= to be replaced by
\!\@\#\$\%\^\&\*\(\)\-\= (8 Replies)
Trying to use code that I found to send only new lines out of a log file by doing:
while :; do
temp=$(tail -1 logfile.out)
awk "/$last/{p=1}p" logfile.out #pipe this to log analyzer program
last="$temp"
sleep 10
done
Script works fine when logfile is basic text, but when it contains... (2 Replies)
Hi All,
In this below script i am not able to find where is "form mail id" is taking when this script is executing i am getting "Controlled Special Account " as from ,i need to send "form mail id " from a table.:mad:
kindly help me plzz.
Regards,
Krupa (0 Replies)
grep -i "$line,$opline" COMBO_JUNK|awk -F, '
{
C4+=$4
}
{
}
END {
print C4
}
' OFS=,`
when i run this command in the script.... it o/p all the value as 0 if $line contains any special parameters.....
but the same script if i run in command prompt... it shows... (4 Replies)
Discussion started by: nikhil jain
4 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)
09-09-2009
