Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Supported but not advertised 1000baseT/Full only in one node of RH cluster
Top Forums UNIX for Advanced & Expert Users Supported but not advertised 1000baseT/Full only in one node of RH cluster Post 302346237 by RuBiCK on Friday 21st of August 2009 10:00:49 AM
Old 08-21-2009
Yes, and ethool shows I commented before:

Code:
# ethtool eth1
Settings for eth1:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full ----> Suppports Gbit
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Full
                                100baseT/Half 100baseT/Full
                                --- Where is Advertised Gbit mode?

 

10 More Discussions You Might Find Interesting

1. HP-UX

i-node full on /var

Can anyone tell me how would I troubleshoot when /var becomes full with inodes? This is on HP11.11 system. Where used is 92%, ifree is 1891 iuse is 88%. Thanks. (3 Replies)
Discussion started by: catwomen
3 Replies

2. Shell Programming and Scripting

The other node name of a SUN cluster

Hello, Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node: # rsh <name> "command" I have to implement this script on all the clusters of my company (a lot of...). Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies

3. HP-UX

Node can't join cluster

Need help guys! when running cmrunnode batch i'm getting this error cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies

4. HP-UX

MC/SG Fail to join cluster node

Hi, Please advise me whereas I have two node cluster server configured with MC/SG. Application and DB are running on Node 1, while Node 2 is standby. All the volume group devices are part of cluster environment. There is only one package running at node 1. Node 2 is having the problem to... (1 Reply)
Discussion started by: rauphelhunter
1 Replies

5. High Performance Computing

Setting up 2 node cluster using solaris 10

hi, i am trying to setup a 2 node cluster environment. following is what i have; 1. 2 x sun ultra60 - 450MHz procs, 1GB RAM, 9GB HDD, solaris 10 2. 2 x HBA cards 3. 2 x Connection leads to connect ultra60 with D1000 4. 1 x D1000 storage box. 5. 3 x 9GB HDD + 2 x 36GB HDD first of all,... (1 Reply)
Discussion started by: solman17
1 Replies

6. Solaris

Active Sun cluster node?

I now the logical name and Virtual IP of the cluster. How can I find the active sun cluster node without having root access? (3 Replies)
Discussion started by: sreeniatbp
3 Replies

7. HP-UX

Identify cluster active node

Hello, Is there any way to identify the active node in a HP-UX cluster without root privileges? (3 Replies)
Discussion started by: psimoes79
3 Replies

8. Solaris

How to remove single node cluster

Hi Gurus, I am very new to clustering and for test i have created a single node cluster, now i want to remove the system from cluster. Did some googling however as a newbee in cluster unable to co related the info. Please help Thanks (1 Reply)
Discussion started by: kumarmani
1 Replies

9. Solaris

SVM metaset on 2 node Solaris cluster storage replicated to non-clustered Solaris node

Hi, Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies

10. AIX

Cluster node not starting

Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies

LEARN ABOUT SUSE

corosync-quorumtool

COROSYNC-QUORUMTOOL(8)					      System Manager's Manual					    COROSYNC-QUORUMTOOL(8)

NAME

       corosync-quorumtool - Set and display quorum settings.

SYNOPSIS

       corosync-quorumtool [-s] [-l] [-v votes] [-n nodeid] [-e expected] [-h] [-i]

DESCRIPTION

       Display the current state of quorum in the cluster and set vote quorum options.

OPTIONS

       -s     show quorum status

       -l     list nodes

       -v <votes>
	      change the number of votes for a node *

       -n <nodeid>
	      optional nodeid of node for -v

       -e <expected>
	      change expected votes for the cluster *

       -h     show nodeids in hexadecimal rather than decimal

       -i     show node IP addresses instead of the resolved name

       -h (if no other argument)
	      show this help text

       * Starred items only work if votequorum is the quorum provider for corosync

SEE ALSO

       corosync_overview(8), votequorum_overview(8),

AUTHOR

       Angus Salkeld

								    2010-05-30						    COROSYNC-QUORUMTOOL(8)
All times are GMT -4. The time now is 08:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy