Sponsored Content
Operating Systems AIX Link aggregation with hacmp ? Post 302345937 by zxmaus on Thursday 20th of August 2009 03:23:18 PM
Old 08-20-2009
Link aggregation with hacmp ?

Hi,

I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch ... would this work or am I thinking wrong somewhere ?

Kind regards
zxmaus
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. IP Networking

bonding without switch link aggregation

I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies

4. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

5. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

6. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

7. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

8. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. Solaris

How can I test link aggregation?

Hi, I have Solaris-10 server and link aggregation is configured on this in below way # dladm show-aggr key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto) device address speed duplex link state bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
setup(1)						      Easy Software Products							  setup(1)

NAME
setup - graphical setup program for the esp package manager SYNOPSIS
setup [ directory ] DESCRIPTION
setup provides a graphical installation interface for EPM-generated portable installation packages. It presents a step-by-step dialog for collecting a list of packages to install and accepting any license agreements for those packages. setup searches for products in the current directory or the directory specified on the command-line. INSTALLATION TYPES
The default type of installation is "custom". That is, users will be able to select from the list of products and install them. setup also supports other types of installations. The setup.types file, if present, defines the other installation types. SEE ALSO
epm(1) - create software packages. setup.types(5) - epm gui setup types file format. COPYRIGHT
Copyright 1999-2007 by Easy Software Products, All Rights Reserved. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MER- CHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. 3 April 2006 ESP Package Manager setup(1)
All times are GMT -4. The time now is 01:49 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy