I receive the error belong when attempting to load the netconsole module. Does anyone know how I can resolve this? I downloaded RPM from internal site, so it is trusted.
>uname -a
Linux indigo 2.6.9-34.ELsmp #1 SMP Fri Feb 24 16:56:28 EST 2006 x86_64 x86_64 x86_64 GNU/Linux
> modprobe -a... (0 Replies)
Hello,
I'm installing a new netdump server and clients.
When I try to start a netdump cliente I get the next error:
/etc/init.d/netdump start ; echo $?
netdump: cannot ping 172.17.128.150
Inicio de netdump /lib/modules/2.4.21-37.ELsmp/kernel/drivers/net/netconsole.o: invalid argument... (3 Replies)
Hi Folks,
Do we have netdump client for Fedora 12 ?
I have downloaded a netdump-server package for the my netdump-server but can't find
netdump client for my FC12 client.
When I installed it via yum, it says
# yum install netdump
Loaded plugins: fastestmirror, presto, security,... (1 Reply)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
hi,
i would like to configure netdump, but saving the var/crash in the server itself, not in another server.
could anybody tell me if this is possible?
thanks (4 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
LEARN ABOUT BSD
lo
LO(4) Kernel Interfaces Manual LO(4)NAME
lo - software loopback network interface
SYNOPSIS
/sys/conf/SYSTEM:
NLOOP 1 # loop-back pseudo-device
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communica-
tion. As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it
is to be used. These addresses may be set or changed with the SIOCSIFADDR ioctl. The loopback interface should be the last interface con-
figured, as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first
unless no hardware interfaces exist.
DIAGNOSTICS
lo%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO intro(4N), inet(4F), ns(4F)BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
3rd Berkeley Distribution August 1, 1987 LO(4)