Hi i 've a M5000 running 2 domains in my Lab with following hardconf
Now i want to partition the 2nd domain further to create a 3rd domain with equal resources on both 2nd and 3rd. For that i set the XSB to quad mode and created the 3rd domin. But now the 3rd domain does not have any network interface and no HDD and the 2nd domain has been deprived of HBA cards. Is it possible to move one HBA card from 3rd to second domain and one network interface from 2nd to 3rd domain ?
Hi,
I 've a fully loaded M5000 which i would like to partition in 4 domains but i have a concern that since we have only 4 internal disks how can we partition the box in for domains with 2 disks ( mirrored ) in each domain. Should i go ahead with 1 Lun from SAN and 1 internal disk for each of 4... (3 Replies)
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Hi
We have an M5000 with one domain running Sun Cluster on it. We would like to split the domain into two domains. One with the existing Sun Cluster and one with a fresh install. We have 2 CPU Boards (8 CPU) / 4 Mem Boards (64 gb memory) and 2 IOU as well as 4 disks
Is it possible to have... (9 Replies)
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Hi Forum
please help me to fix M5000 Server which we were not using. now i logged to serve and foung that everything is showing as Deconfigured.
XSCF> showhardconf
SPARC Enterprise M5000;
+ Serial:BDF1051F30; Operator_Panel_Switch:Locked;
+ Power_Supply_System:Single;... (4 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
on an m5000 , I can not power it up, system failure.
XSCF> poweron -a
DomainIDs to power on:00,01
Continue? :y
00 :Not powering on :Poweron canceled due to missing component.
01 :Not powering on :Poweron canceled due to missing component.
the only fault that I can see is:
... (4 Replies)
Discussion started by: goya
4 Replies
LEARN ABOUT PLAN9
install-solaris
install-solaris(1M)install-solaris(1M)NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)