06-26-2009
Quote:
Originally Posted by
incredible
Do one simple test. ensure that the IP on your system is plumbed up and is "UP". configure your laptop to an IP of the same subnet and see if you can ping. This will tell your if your Nic is good or not
That's incorrect. If you configure a laptop on the same subnet and try to ping the server, that ping still has to go through the laptop's NIC, the cable to the patch panel, the switch port the patch panel is connected to, the other switch port, the other patch panel, the cable from the patch panel to the server, then the server NIC. IF you ping doesn't go through, where's the problem? It could be any of the points mentioned above.
The right test woulb be to configure a laptop with the IP of the server and plug it right to the very same cable that plugs into the server.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
4. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
5. Solaris
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. Solaris
Hi All,
1. modify /etc/default/login file as
make commented # console=
2.put my laptops ip at both
/etc/inet/ipnodes and /etc/host file
still i can login via telnet/ftp through a DB9-serial cable, but when i tried
through a lan stratight cable directly connected that machine... (7 Replies)
Discussion started by: mahadib
7 Replies
8. Solaris
Hi all,
really interesting thing I have encountered . So :
root@host4 # uname -a
SunOS host4 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-880
root@host4 # scinstall -p
3.2
latest recommended patches applied ..all SUN cluster patches applied.
SUN cluster software installed without... (2 Replies)
Discussion started by: samar
2 Replies
9. Solaris
We are unable to ping from Sun Ultra 60 to Ultra 10 machine and vice versa. We are getting an error message Cable Link Down ?. It was working fine.
Troubleshooting steps taken.
1) Changed the IPaddresses on both machines 192.168.10.10 and 192.168.10.20. These machines connected through 8 port... (2 Replies)
Discussion started by: vijaykrishna
2 Replies
10. Red Hat
I am facing strange problem regarding hostname on my Linux(2.6.18-164.el5xen x86_64 GNU/Linux), the hostname changes if reboot with lan cable and with NO lan cable
Reboot with lan cable:
The hostname is ubunut
Unable to connect Oracle database using sqlplus some times database is not... (2 Replies)
Discussion started by: LinuxLearner
2 Replies