Visit Our UNIX and Linux User Community

Full Discussion: T2000 Hardware RAID
Operating Systems Solaris T2000 Hardware RAID Post 302307604 by incredible on Wednesday 15th of April 2009 11:03:03 PM
Old 04-16-2009
Its hot-swappable. You can just pull out the disk while the system is running or you can bring the system down to the OK> prompt then pull out the disk you want to.
 
Test Your Knowledge in Computers #578
Difficulty: Medium
Lists are ordered collections that are essentially static arrays.
True or False?

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID

I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies

2. Solaris

How to setup hardware RAID on a T2000

Hello all We've just bought a T2000. It has two disks and I'm trying to figure out how to create a mirror of the boot disk. I understand that I have to boot into single user mode from DVD and then use the raidctl command to set up the mirror and label the volume afterwards. Format returns... (4 Replies)
Discussion started by: soliberus
4 Replies

3. Solaris

T2000 RAID Question

New to the boards here so please bear with me! I have a T2000 server with Solaris 10 installed on it. Disk 0 is the only disk currently being used, as I do NOT have a RAID set up. Disk 1 is just sitting there looking pretty. I'd like to set up a mirrored RAID in order to fully utilize both... (5 Replies)
Discussion started by: phi148
5 Replies

4. Solaris

Raid problem on T2000

Hi all, First post so be gentile :) It's my first time installing Solaris on T2000 server. I have 2 72GB HD's on it. After configuring HW raid and running raidctl command I get this output: bash-3.00# raidctl -l c0t0d0 Volume Size Stripe Status Cache RAID ... (2 Replies)
Discussion started by: Obi-Wan
2 Replies

5. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help. (2 Replies)
Discussion started by: presul
2 Replies

6. Solaris

Hardware Raid - LiveUpgrade

Hi, I have a question. Do LiveUpgrade supports hardware raid? How to choose the configuration of the system disk for Solaris 10 SPARC? 1st Hardware RAID-1 and UFS 2nd Hardware RAID-1 and ZFS 3rd SVM - UFS and RAID1 4th Software RAID-1 and ZFS I care about this in the future to take... (1 Reply)
Discussion started by: bieszczaders
1 Replies

7. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies

8. Hardware

Sun T3-1 hardware RAID

Hi all I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS. The documentation doesn't make it clear if: 1. The... (6 Replies)
Discussion started by: soliberus
6 Replies

9. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My... (4 Replies)
Discussion started by: KhawHL
4 Replies
ATARAID(4)						   BSD Kernel Interfaces Manual 						ATARAID(4)

NAME
ataraid -- ATA software RAID support SYNOPSIS
device ata device ataraid DESCRIPTION
The ataraid driver provides support for so-called software RAID (sometimes referred to as fake RAID or pseudo RAID). When a controller that supports software RAID is instructed to create a RAID array, its BIOS writes data structures in a specific metadata format to the disks. These data structures are picked up by the ataraid driver, so that FreeBSD can work with the array. The ataraid driver has to understand the specific metadata format of a controller BIOS in order to support its RAID capabilities. Read-only support for a metadata format means that FreeBSD can use the given RAID array for normal read/write operations. Creation and rebuild of such arrays has to be done from the controller BIOS. Read and write support for a metadata format means that FreeBSD can use the given RAID array for normal read/write operations. Additionally, the atacontrol(8) utility can be used to create, rebuild, update and fail such RAID arrays. The ataraid driver can read the following metadata formats: o Adaptec HostRAID o Highpoint V2 RocketRAID o Highpoint V3 RocketRAID o Intel MatrixRAID o Integrated Technology Express (ITE) o JMicron o LSI Logic V2 MegaRAID o LSI Logic V3 MegaRAID o NVIDIA MediaShield o Promise FastTrak o Silicon Image Medley o Silicon Integrated Systems (SiS) o VIA Tech V-RAID o FreeBSD PseudoRAID The ataraid driver can write the following metadata formats: o Highpoint V2 RocketRAID o Intel MatrixRAID o JMicron o Promise FastTrak o Silicon Integrated Systems (SiS) o VIA Tech V-RAID o FreeBSD PseudoRAID It is also possible to use software RAID on controllers that do not have special software RAID capabilities. See atacontrol(8) for details. FILES
/dev/ar* ATA RAID device nodes SEE ALSO
ata(4), atacontrol(8) CAVEATS
RAID5 is not supported at this time. Code exists, but it neither uses nor maintains parity information. AUTHORS
The ataraid driver was written by Soren Schmidt <sos@FreeBSD.org>. This manual page was written by Christian Brueffer <brueffer@FreeBSD.org>. BSD
February 17, 2006 BSD

Featured Tech Videos

All times are GMT -4. The time now is 12:43 AM.
Unix & Linux Forums Content Copyright 1993-2020. All Rights Reserved.
Privacy Policy