04-15-2009
I am planning to patch my system and unplug disk0 as fallback plan. My concern is whether it will crash my system by the time i boot from disk2? I only have /pci@780/pci@0/pci@9/scsi@0/sd@0,0 (disk0 path) in my OBP boot-device. Would it be suffice as there isn't any disk2 path available.
9 More Discussions You Might Find Interesting
1. Solaris
I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies
2. Solaris
Hello all
We've just bought a T2000. It has two disks and I'm trying to figure out how to create a mirror of the boot disk. I understand that I have to boot into single user mode from DVD and then use the raidctl command to set up the mirror and label the volume afterwards.
Format returns... (4 Replies)
Discussion started by: soliberus
4 Replies
3. Solaris
New to the boards here so please bear with me!
I have a T2000 server with Solaris 10 installed on it. Disk 0 is the only disk currently being used, as I do NOT have a RAID set up. Disk 1 is just sitting there looking pretty.
I'd like to set up a mirrored RAID in order to fully utilize both... (5 Replies)
Discussion started by: phi148
5 Replies
4. Solaris
Hi all,
First post so be gentile :)
It's my first time installing Solaris on T2000 server.
I have 2 72GB HD's on it.
After configuring HW raid and running raidctl command I get this output:
bash-3.00# raidctl -l c0t0d0
Volume Size Stripe Status Cache RAID
... (2 Replies)
Discussion started by: Obi-Wan
2 Replies
5. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
6. Solaris
Hi,
I have a question. Do LiveUpgrade supports hardware raid?
How to choose the configuration of the system disk for Solaris 10 SPARC?
1st Hardware RAID-1 and UFS
2nd Hardware RAID-1 and ZFS
3rd SVM - UFS and RAID1
4th Software RAID-1 and ZFS
I care about this in the future to take... (1 Reply)
Discussion started by: bieszczaders
1 Replies
7. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
8. Hardware
Hi all
I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS.
The documentation doesn't make it clear if:
1. The... (6 Replies)
Discussion started by: soliberus
6 Replies
9. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
LEARN ABOUT DEBIAN
pci-config
PCI-CONFIG(8) System Manager's Manual PCI-CONFIG(8)
NAME
pcnet-diag - EEPROM setup and diagnostic program for ethernet cards based on the AMD PCnet/PCI series chips.
SYNOPSIS
pci-config [options]
DESCRIPTION
pci-config is a program that you can use to diagnose problems with ethernet cards
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-# <device-index>
Operate only on device <device-index>.
-a, --show_addresses
Show PCI registers
-S, --sleep
Put device to sleep (ACPI D3).
-W, --wake
Wake a sleeping device (ACPI D0 state).
-B, --bus <bus>
Show only devices on BUS.
-A, --set-addresses <addr>
Set PCI address register 1 to the <addr>.
-D, --debug
Show details of operations.
-f, --force
Override checks and perform the operation.
-u, --usage
Show a long usage message.
SEE ALSO
mii-diag(8)
AUTHOR
pci-config was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 PCI-CONFIG(8)