04-06-2009
Hi all,
My requirement is to read network traffic int userlevel . I am using C programming in Centos 5 with 2.6.18 kernel.
For example can i read the file contents which I copied using SCP . That I want the data part of the network traffic leaving out headers and tailors..Pludi, you said there are some higher level abstractions for easier access in some libraries... What do you mean by that..Where can I look for the same...Please help me out..
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Solaris
I do have a server (SUNV240) with Solaris 9, it has a PCI gigaswift ethernet card for fiber with SC connector, everytime I reboot the server the card won't link up unless I unplug it and plug it back again, for remote operations this is a hassle since sometimes reboots are needed and this card... (3 Replies)
Discussion started by: xe2bss
3 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies