04-02-2009
Netra Remote Dial-in Problem
Looking for ideas on why I can't dial into our new Avaya CMS server (Sun Netra 210 - Sol 9) - remotely thru our ASA - site admin software.
Running R3-V13 Avaya CMS software - just did a fresh install of the CMS software - install went perfect.
The Sun supplied DB9 connector is installed correctly on the Netra and the DB25 connector on the Sportster 33.6 and the factory CAT5 cable is connected to the DB9 & DB25.
ASA software settings are exactly what I use to dial remote to all our switches & VMs - 8-N-1 Hardware - Emulation 4425 (from my IBM Notebook) and I have tried the analog modem setting ... generic 1200/2400/9600 - generic 9600 etc and while the modem answers and handshakes every time - and the ASA terminal Emulation screen opens up when connected - I cannot get a Login.
This is driving me crazy. Should be simple. I have tried (4) different Sportster 33.6 modems - same result.
I put an RS-232 tester on the DB25 connector from the CMS - no connecttion to the Sportser yet - got green LED on TD & Red on RTS & DTR. When I connected the tester w/ the DB25 to the Sportser and turned it on - Green was TD-CD-RD & Red was RTS-DSR-CTS-DTR. When I dialed into the CMS - and got a successful handshake - the TD & RD were green and other LEDs were red .... but no data shows on the ASA terminal screen?
Very strange. I'm guessing it is something simple so any help or tips would be helpful.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I'd like to know if it is possible to set up a Dial Up server on a Red Hat 7.1 Instalation so that friends/colleagues can dial into my computer and log in (eg. SLIP/PPP)? Or if i'd have to download any other software with which to do this. And if so, where would I find something good... (2 Replies)
Discussion started by: KrazyGuyPaul
2 Replies
2. UNIX for Dummies Questions & Answers
Hi all.
I am running a C++ program on UNIX which needs days to finish but my dial-up connection disconnects after 4 hours. Is there any way for the program to keep running until it finishes after I log out? (5 Replies)
Discussion started by: vegas503
5 Replies
3. SCO
Friends,
I am facing a problem in connecting two SCO Openserver 5.0.6 servers through Dial-Up connectivity as is done in the case of two Windows PCs. Please help me out with the following problems:
(a) How to configure the modem?
(b) How to setup a Dial-In connection?
(c) How to... (1 Reply)
Discussion started by: thecobolguy
1 Replies
4. Solaris
Hey All
Thanks in Advance.
Iam facing a problem with Netra T1 105 Ram issuse.I have 1 gb ram in the server but when it boots up in ok prompt or in banner it shows 768 mb Ram , if i put 512 mb Ram it show 368 mb Ram but this all ram if i connect in anthore netra server its shows 1 gb and... (1 Reply)
Discussion started by: solaris8in
1 Replies
5. Solaris
I am looking for a dial-up remote printing solution as under :
1. We have a Centralized location where Sun Solaris (A) is installed. From here printing command will be despatched.
2. This printing command will be routed to WAN cloud to Main Branches (B1,B2,B3)and from there, printer at... (0 Replies)
Discussion started by: jayvee
0 Replies
6. UNIX for Dummies Questions & Answers
I was wondering if anyone can tell me if i can run Unix to the internet? (1 Reply)
Discussion started by: slade
1 Replies
7. Ubuntu
My current hardware config is:
Processor
1.85 gigahertz AMD Athlon XP
64 kilobyte primary memory cache
512 kilobyte secondary memory cache
HDS722540VLAT20 (41.17 GB) -- C
BENQ DVD DD DW1650 -- E
JLMS XJ-HD166S -- D
3.5" format removeable media -- A
Main Circuit Board
Board:... (1 Reply)
Discussion started by: XP_2600
1 Replies
8. Solaris
Hello,
I wrote a script which monitor the keyswitch state repeatedly each 10 minutes.
I'm extracting the keyswitch status by using prtdiag.
The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status.
unlike Netra 440 server , I found that... (2 Replies)
Discussion started by: Alalush
2 Replies
9. Solaris
Hi,
I have a netra t2000 running solaris 10. It is fully patched with the latest patch cluster and also patch 118833-36 and 126897-02. The SC sys_event level is set to 3.
I am running a test to show hardware log status, e.g simulating a power supply failure.Hence I unplug one of te... (3 Replies)
Discussion started by: ulemsee
3 Replies
10. Solaris
hey guys i'm in university and i bought my self a sun ultra SPARC netra 500mhz machine with the usb ports a vga gfc and cdrom drive
now i have a problem (bought it off ebay) i trying to install a fresh solaris 10 server op onto it but it looks like it previously had linix installed and... (38 Replies)
Discussion started by: garethmob
38 Replies