Special Forums IP Networking port access to site to site VPN Post 302268342 by photon on Monday 15th of December 2008 12:19:57 PM
port access to site to site VPN

Setup a site to site VPN between two cisco routers.

One of the site locations is unable to access ports such as https://example.com:9001

How do I let them go into port 9001?

They can ssh, ftp, telnet and everything else.

Is this a VPN issue or ACL access issue?

I put
permit ip host 10.0.0.0 host 192.0.0.0

tried adding this
permit tcp host 10.0.0.3 host 192.0.0.5
but nothing

so they should be able to access???Smilie
 
Test Your Knowledge in Computers #749
Difficulty: Medium
The ZX81 had a base configuration of 1 KB of on-board memory that could officially be expanded externally to 64 KB.
True or False?

9 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

How to check site access in shell script

Hello every one, I have a little issue that has been killing me now for the past couple of days, I have tried to find solutions online, but its been hard to, ok here it goes... I have created a site that is based on amount of user that have access at a time, based on cookie. So if the browser... (1 Reply)
Discussion started by: heman007
1 Replies

2. UNIX for Advanced & Expert Users

squid: Allow access to only one site and only via 80 or 443

Can someone please give me the conf file line to allow access to myexample.com and only that site, and only through http and https? So far I have only that site accessible via http, but all https sites are opened. Squid 3.1 on Cent 6 ---------- Post updated at 12:06 PM ---------- Previous... (0 Replies)
Discussion started by: glev2005
0 Replies

3. IP Networking

How to establish site to site vpn - Linux machine and cisco asa?

Hi, I am trying to establish vpn between my linux server and cisco asa at client side. I installed openswan on my cent os. Linux Server eth0 - 182.2.29.10 Gateway - 182.2.29.1 eth1 - 192.9.200.75 I have simple IPtables Like WAN="eth0" LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies

4. Red Hat

Want to unblock port for particular site

Dear All We have one Centos Server on Asterisk platform.We are trying to open one particular site from client machines which is our client portal.We have to upload data on that.When we trying to open that site somewhere its blocking and not opening.We did tracert and found one router down... (3 Replies)
Discussion started by: Vaibhav.T
3 Replies

5. IP Networking

VPN ssh access over RDP port?

Guys, Can I use an open RDP port to gain ssh access to my Linux server running the other side of our firewall? I work from home on the odd occasion, we only have RDP port 3389 available once logged into the VPN. I would rather ssh into my workstation without the need for a desktop display. ... (3 Replies)
Discussion started by: general_lee
3 Replies

6. IP Networking

iptables allow access to one site

Hi all I need help with a set of iptables rules that would allow a portion of a bank of ipaddresses acces to only one or two named wbsites. Please advise Thank You Ed (3 Replies)
Discussion started by: wa1ed
3 Replies

7. IP Networking

Does cisco 1921 router support site to site VPNs using IPSec?

Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? " A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies

8. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

9. Post Here to Contact Site Administrators and Moderators

Regarding not able to access UNIX.com site

Hello MODs/Admins, Could you please help me here as from last 6 to 7 days I(and checked with my fellow friends too) am not able to access unix.com site at all. It is very very slow, it never loads completely. Even I checked with different people and different computers it results same only,... (8 Replies)
Discussion started by: RavinderSingh13
8 Replies
AGGREGATE-IOS(1)                                              General Commands Manual                                             AGGREGATE-IOS(1)

NAME
aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short. SYNOPSIS
aggregate-ios <source_config >optimised_config DESCRIPTION
Takes cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1). Optimised filters are produced on std- out. OPTIONS
None. DIAGNOSTICS
Any diagnostics produced by aggregate(1) are passed through on stderr. EXAMPLES
The following configuration fragment: ip prefix-list AS65530 description Foo, Inc ip prefix-list AS65530 permit 10.1.0.0/16 ip prefix-list AS65530 permit 10.2.0.0/16 ip prefix-list AS65530 permit 10.2.1.0/24 ip prefix-list AS65530 permit 10.3.0.0/16 ip prefix-list AS65531 description Bar.Com ip prefix-list AS65531 seq 5 permit 192.168.1.0/24 ip prefix-list AS65531 seq 10 permit 192.168.2.0/24 ip prefix-list AS65531 seq 15 permit 192.168.0.0/19 is optimised as follows: ip prefix-list AS65530 permit 10.1.0.0/16 le 24 ip prefix-list AS65530 permit 10.2.0.0/15 le 24 ip prefix-list AS65531 permit 192.168.0.0/19 le 24 SEE ALSO
aggregate(1) HISTORY
Aggregate-ios was written by Joe Abley <jabley@mfnx.net>. BUGS
All those in aggregate(1) and then some :) Joe Abley 2000 November 27 AGGREGATE-IOS(1)

Featured Tech Videos

All times are GMT -4. The time now is 06:10 AM.
Unix & Linux Forums Content Copyright 1993-2019. All Rights Reserved.
Privacy Policy