10-31-2008
Quote:
Originally Posted by
acascianelli
[...] I am assured that there is no problems with the switch configuration[...]
Well..... Your etherchannel configuration seems OK to me but the server side is only half of the equation. Use
# entstat -d ent2
to find out if there are errors visible on the physical interfaces and the link aggregation status. Use the information from
IBM Systems Information Center to get detailed status information. If necessary get back to the switch admin to find out whether your Etherchannel config works with the switch port setup.
10 More Discussions You Might Find Interesting
1. AIX
Problem description:
On the condition of EtherChannel function of AIX, when the data exchange between the nodes on the network, there sometimes lost datat packets and cause the application failed. Once we deconfig EtherChannel and use the single adapter configuration, the application works... (0 Replies)
Discussion started by: Frank2004
0 Replies
2. AIX
I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks. (5 Replies)
Discussion started by: jwholey
5 Replies
3. AIX
I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8.
when I run the command
lsattr -El ent8
I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But... (10 Replies)
Discussion started by: thenomad
10 Replies
4. BSD
Hi Buddies!
I need to do a new kind of setting in FreeBSD (i'm a newbie using this OS).
Interface 1 y 2 in Trunk/Etherchannel mode
IP-> xx.xx.xx.xx
netmask-> 255.255.255.0
Anybody can help me with a step by step Guide?.
THANKS A MILLION!!! (1 Reply)
Discussion started by: dagomez09
1 Replies
5. AIX
Hello,
On a partition with AIX 5300-11-01-0944.
1 etherchannel ent9 with aggregation ent3/ent7.
# lsdev |grep ent
...
ent3 Available 07-01 4-Port 10/100/1000 Base-TX PCI-Express Adapter (14106803)
...
ent7 Available 0A-01 4-Port 10/100/1000 Base-TX PCI-Express... (2 Replies)
Discussion started by: Trunk
2 Replies
6. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
7. AIX
I have few AIX servers in my data center, which have their EtherChannel configured to have a fat pipe (active/active) and a nagios server to monitor the server uptimes. Nagios server pings every server in the data center and we have pretty much every known unix flavor in this data center. When... (3 Replies)
Discussion started by: thenomad
3 Replies
8. AIX
Hi,
I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches.
I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels)
But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies
9. AIX
Hi Guys,
I am trying to test an etherchannel failover and switchback.
I did failover from primary to backup adapter, but now I am not able to switch it back to primary.
phcxxxxx:/ > entstat -d ent4 | grep Active
Active channel: backup adapter ... (1 Reply)
Discussion started by: snchaudhari2
1 Replies
10. AIX
Hello,
POWER7 machine.
4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA.
If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if... (3 Replies)
Discussion started by: vilius
3 Replies
LEARN ABOUT CENTOS
imsettings-switch
imsettings-switch(1) imsettings-switch(1)
NAME
imsettings-switch - Switch Input Method
SYNOPSIS
imsettings-switch [ -hnqrx ] [ --no-update ] [ --quiet ] [ --restart ] [ --read-xinputrc ] [ --help ] [Input Method name | configuration
filename]
DESCRIPTION
imsettings-switch switches Input Method which is managed under imsettings. Either Input Method name or configuration filename are required
unless --read-xinputrc option is specified to determine the target from $HOME/.config/imsettings/xinputrc or $xinputrcdir/xinputrc.
OPTIONS
This program follows the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included
below.
-n --no-update
Do not update $HOME/imsettings/xinputrc. without this option, imsettings-switch will updates it with the targeted Input Method.
-q --quiet
Do not show any messages except errors.
-r --restart
Restart the given Input Method or one which is determined from xinputrc by --read-xinputrc option.
-x --read-xinputrc
Determine the targeted Input Method from $HOME/imsettings/xinputrc or $xinputrcdir/xinputrc if not available.
-h --help
Show summary of options
Input Method name
Switch Input Method to Input Method name.
configuration filename
Switch Input Method to configuration filename.
SEE ALSO
imsettings-list(1) imsettings-reload(1)
AUTHOR
This manual page was written by Akira TAGOH <akira@tagoh.org>
Apr 10, 2013 imsettings-switch(1)