Sponsored Content
Operating Systems SCO Sco 5.06 How To Mount A 2nd Hdd Help Help!!!! Post 302193577 by fabtagon on Friday 9th of May 2008 07:51:23 PM
Old 05-09-2008
I've never used SCO. Systematic way goes as follows:

What gives the shell command "mount"? That will be some lines with (mountpoint, hardware, options) tupels to you. Have a look at the hardware part. In some way the SCSI ID will be part of device file. Alter that file to match the old drive. Mount it with "mount /dev/olddevice /mnt/dir_for_old_drive" (create dir before, act as root).
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

SCO UNIX HDD full backup

HI ALL, I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies

2. SCO

SCO 5.0.7 and Serial ATA HDD question

Hi guys, I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this. I'm not using any raid, just one HDD. Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies

3. UNIX for Advanced & Expert Users

SCO 5.0.5 installation on 80GB HDD

Hello, I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE . I have tried the following techniques: 1. using the updated wd btld image- no success 2. defbootstr biosgeom 3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies

4. Solaris

How to mount External HDD in VMware 6.0

Hi Friends, I am using VMware 6.0 and i want to transfer some files from External HDD so how to mount the Disk, and i am not able to assign any ip to my network card any one can help me how to set ip in VMware. Thanks and Regards, Venky.:b: (0 Replies)
Discussion started by: 1409.venkatesh
0 Replies

5. Windows & DOS: Issues & Discussions

NFS HDD mount on Windows XP

Hi, Unix based, My harddrive won't boot and I'm looking for a reliable tool that can mount a hdd on Windows XP and show me the files stored on a NFS system. I tried the tool: Ext2IFS but this didn't work. I found a lot of tools on google to mount nfs share thru a network but that's... (1 Reply)
Discussion started by: severt
1 Replies

6. Filesystems, Disks and Memory

How to mount and read vintage scsi HDD

I started on another thread and full story can be seen here: https://www.unix.com/security/91428-how-reset-root-password-old-unix-system-v.html But my situation turned to land on this thread now. I have old scsi HDD out of the UHC UNIX System V Rel. 4.0 Version 3.6 box. And need to read... (1 Reply)
Discussion started by: 82026
1 Replies

7. SCO

Dd (raw) image of SCO 5.0.6 mount as second hdd

Hi all I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB . Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies

8. Solaris

How to mount ntfs for storage HDD new to Solaris 11.2?

I just installed Solaris 11.2 - and it is a bugger. How do I mount an extra HDD that is now formated to NTFS through gparted it keeps telling me I don't have any ntfs on this laptop. it has two hdds, /dev/sda1 /dev/sdb1 (Linux lingo) Solaris is installed on primary hard drive back of it. then... (2 Replies)
Discussion started by: userx-bw
2 Replies

9. Fedora

Fstab for 2nd hdd, how to?

once again, mounting another volume or hdd the fstab-file is giving me a headache. May someone could give me a hint how to configure the fstab-file properly to use the hdd. The following ls -l /dev/disk/by-uuidis giving me this Thats the UUID for /dev/sdb1 with the name "save"... (6 Replies)
Discussion started by: 1in10
6 Replies

10. Emergency UNIX and Linux Support

2nd hdd is Linux_lvm can't mount MBR on BSD with GPT

rying it this way, because I can't handle the slices for the second hdd. If there is someone on this forum who can help me out of that misery, he would really save my digital life in this digital ocean. So not giving up, reading several times the manual of gpart. But the best hint in all that... (0 Replies)
Discussion started by: 1in10
0 Replies
DMC(1)																	    DMC(1)

NAME
dmc - controls the Disk Mount Conditioner SYNOPSIS
dmc start mount [profile-name|profile-index [-boot]] dmc stop mount dmc status mount [-json] dmc show profile-name|profile-index dmc list dmc select mount profile-name|profile-index dmc configure mount type access-time read-throughput write-throughput [ioqueue-depth maxreadcnt maxwritecnt segreadcnt segwritecnt] dmc help | -h DESCRIPTION
dmc(1) configures the Disk Mount Conditioner. The Disk Mount Conditioner is a kernel provided service that can degrade the disk I/O being issued to specific mount points, providing the illusion that the I/O is executing on a slower device. It can also cause the conditioned mount point to advertise itself as a different device type, e.g. the disk type of an SSD could be set to an HDD. This behavior consequently changes various parameters such as read-ahead settings, disk I/O throttling, etc., which normally have different behavior depending on the underlying device type. COMMANDS
Common command parameters: o mount - the mount point to be used in the command o profile-name - the name of a profile as shown in dmc list o profile-index - the index of a profile as shown in dmc list dmc start mount [profile-name|profile-index [-boot]] Start the Disk Mount Conditioner on the given mount point with the current settings (from dmc status) or the given profile, if pro- vided. Optionally configure the profile to remain enabled across reboots, if -boot is supplied. dmc stop mount Disable the Disk Mount Conditioner on the given mount point. Also disables any settings that persist across reboot via the -boot flag provided to dmc start, if any. dmc status mount [-json] Display the current settings (including on/off state), optionally as JSON dmc show profile-name|profile-index Display the settings of the given profile dmc list Display all profile names and indices dmc select mount profile-name|profile-index Choose a different profile for the given mount point without enabling or disabling the Disk Mount Conditioner dmc configure mount type access-time read-throughput write-throughput [ioqueue-depth maxreadcnt maxwritecnt segreadcnt segwritecnt] Select custom parameters for the given mount point rather than using the settings provided by a default profile. See dmc list for example parameter settings for various disk presets. o type - 'SSD' or 'HDD'. The type determines how various system behaviors like disk I/O throttling and read-ahead algorithms affect the issued I/O. Additionally, choosing 'HDD' will attempt to simulate seek times, including drive spin-up from idle. o access-time - latency in microseconds for a single I/O. For SSD types this latency is applied exactly as specified to all I/O. For HDD types, the latency scales based on a simulated seek time (thus making the access-time the maximum latency or seek penalty). o read-throughput - integer specifying megabytes-per-second maximum throughput for disk reads o write-throughput - integer specifying megabytes-per-second maxmimu throughput for disk writes o ioqueue-depth - maximum number of commands that a device can accept o maxreadcnt - maximum byte count per read o maxwritecnt - maximum byte count per write o segreadcnt - maximum physically disjoint segments processed per read o segwritecnt - maximum physically disjoint segments processed per write dmc help | -h Display help text EXAMPLES
dmc start / '5400 HDD' Turn on the Disk Mount Conditioner for the boot volume, acting like a 5400 RPM hard drive. dmc configure /Volumes/ExtDisk SSD 100 100 50 Configure an external disk to use custom parameters to degrade performance as if it were a slow SSD with 100 microsecond latencies, 100MB/s read throughput, and 50MB/s write throughput. IMPORTANT
The Disk Mount Conditioner is not a 'simulator'. It can only degrade (or 'condition') the I/O such that a faster disk device behaves like a slower device, not vice-versa. For example, a 5400 RPM hard drive cannot be conditioned to act like a SSD that is capable of a higher throughput than the theoretical limitations of the hard disk. In addition to running dmc stop, rebooting is also a sufficient way to clear any existing settings and disable Disk Mount Conditioner on all mount points (unless started with -boot). SEE ALSO
nlc(1) January 2018 DMC(1)
All times are GMT -4. The time now is 06:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy