04-25-2008
All SCSI tape drives do not require any drivers for it. You just need to know which SCSI host adapter that you are connecting it to. Check which SCSI host adapter you have / buy and make sure you have the correct drivers available for you OpenServer 5 level. There were / are several levels of OpenServer 5 and some drivers are not always available for each level.
Last edited by uxlunatick; 04-25-2008 at 10:55 AM..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I tried to install Magneto-Optical (MO) drive Fujutsu to COMPAQ Proliant ML350 with SCO Openserver 5.0.5. Harddisk and MO are connected to Adaptec UW-SCSI-3 (driver ad160).
During boot process system shows me that MO is connected to host adapter 1, bus 0, SCSI ID 1 and LUN 0. But when I... (2 Replies)
Discussion started by: yurist
2 Replies
2. UNIX for Advanced & Expert Users
hi everybody
I have got a set of sco unix open server release 3.0 flopyy disks series N1, N2, M1, P1...P43, Release notes..
ý did a fresh installation. but ý cant install ethernet card. when ý use netconfig-ad a chain -tcpip... there is a messge :
the sco contain TCP/IP driver. and ý... (2 Replies)
Discussion started by: kaygusuz
2 Replies
3. UNIX for Advanced & Expert Users
Hi guys
I had a system running 5.0.6 , we upgraded it to 5.0.7 everything was fine till i try to do a test backup.
The error was cannot open (cannot open /dev/xct0 no such file or directory)what i did was, removed the tape , reboot the system and the try to install it again, but its... (2 Replies)
Discussion started by: josramon
2 Replies
4. UNIX for Dummies Questions & Answers
I need to run a back up that will take more than one tape. What is the command that will continue the back up on to a second tape drive. the first is /dev/rStp0 second is /dev/rStp1. Anyone? (1 Reply)
Discussion started by: franruiz
1 Replies
5. SCO
Hi
Don't know if anyone will be able to help, but we're currently having problems with our external tape drive on our SCO server. If I try the following command for instance, "tar cvf /dev/rStp0", the tape drive jumps into action for a while, then comes back with the error "tar: cannot open:... (3 Replies)
Discussion started by: mattingg
3 Replies
6. UNIX for Dummies Questions & Answers
hi guys,
I.m trying to remove and add a new tape drive by using the mkdev tape command and when i try to update the Kernel this is what i'm getting,
i386ld: Symbol Sdsk_no_tag in /var/opt/K/SCO/link/1.1.1Eb/etc/conf/pack.d/blad/s
pace.o is multiply defined. First defined in... (0 Replies)
Discussion started by: josramon
0 Replies
7. SCO
Hello All,
I m new in SCO.Please any one help me regarding configuring HP TapeDrive in SCO OPENSERVER5. (1 Reply)
Discussion started by: ather_36
1 Replies
8. SCO
Hello,
I've a Dell computer Poweredge 1800 with a Perc DC4 Dual channel raid controller :D . The whole computer is SCSI based .
I've installed the whole system (SCO 6.0, maintenance package 2.0, and our Openbasic software and all printers).
Everything works, even my remote printers.
But I've... (2 Replies)
Discussion started by: frederik1
2 Replies
9. SCO
Does anybody know the commands to access the data from a pen drive in a SCO Openserver 6.
What are the parameters to the mount command for accessing the USB port:confused: (9 Replies)
Discussion started by: jksah
9 Replies
10. SCO
Our tape drive died and I installed a newer Quantum DAT72 drive in it's place with the same SCSI ID. It still works, but with one major flaw, the system will lock up if I try to upgrade BackupEDGE or view NFS settings in scoadmin.
I get a Transition to ready failure on ha=0* message when the... (4 Replies)
Discussion started by: psytropic
4 Replies