04-17-2008
PCI / PCIExpress Parallel port in SCO 6.0.0
How do or what do I need to add PCI / PCIe (PCI Express) parallel ports add-on adapters to OpenServer 6.0.0? OpenServer 5 could see PCI slots but OpenServer 6.0.0 (Original CD or the Re-cut one) required a maintenance pack to be installed? Is this right and how do I check to see if these work?
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
2. Programming
Hi I'm trying to look for information about reading/writing to the parallel port of a Sun Ultra 5 running Solaris 8. I'd just like to see some basic programs written in C, nothing fancy, just reading and wrting to the port, getting the port address etc. toggling the lines.
I've tried searching... (2 Replies)
Discussion started by: fishman2001
2 Replies
3. UNIX for Dummies Questions & Answers
I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies
4. UNIX for Advanced & Expert Users
I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies
5. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I am trying to add a parallel printer to my SCO OSR6 server, yet when I run mkdev parallel it just brings up the message: "Parallel Ports are configured automatically in SCO Openserver 6".
So when I try and add a local printer, no /dev/lp# ports are shown in the list, only serial ports... (1 Reply)
Discussion started by: Martyn
1 Replies
7. Fedora
Greetings,
A sort of newbie question...
I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies
8. AIX
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies
9. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
LEARN ABOUT FREEBSD
pccbb
PCCBB(4) BSD Kernel Interfaces Manual PCCBB(4)
NAME
pccbb -- cardbus bridge driver
SYNOPSIS
device cbb
device pccard
device cardbus
device exca
DESCRIPTION
The pccbb driver implements the Yenta specification for CardBus bridges.
The following PCI cardbus and pcmcia bridges are supported:
Cirrus Logic PD6832
Cirrus Logic PD6833
Cirrus Logic PD6834
O2micro OZ6812
O2micro OZ6832
O2micro OZ6833
O2micro OZ6836
O2micro OZ6860
O2micro OZ6872
O2micro OZ6912
O2micro OZ6922
O2micro OZ6933
O2micro OZ6972
O2Micro OZ711E1
O2Micro OZ711M1
Ricoh RL4C475
Ricoh RL4C476
Ricoh RL4C477
Ricoh RL4C478
TI PCI-1031
TI PCI-1130
TI PCI-1131
TI PCI-1210
TI PCI-1211
TI PCI-1220
TI PCI-1221
TI PCI-1225
TI PCI-1250
TI PCI-1251
TI PCI-1251B
TI PCI-1260
TI PCI-1260B
TI PCI-1410
TI PCI-1420
TI PCI-1450
TI PCI-1451
TI PCI-1510
TI PCI-1515
TI PCI-1520
TI PCI-1530
TI PCI-1620
TI PCI-4410
TI PCI-4450
TI PCI-4451
TI PCI-4510
TI PCI-4520
TI PCI-[67]x[12]1
TI PCI-[67]x20
ENE CB710
ENE CB720
ENE CB1211
ENE CB1255
ENE CB1410
ENE CB1420
Toshiba ToPIC95
Toshiba ToPIC95B
Toshiba ToPIC97
Toshiba ToPIC100
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.cbb.debug Non-zero values cause more verbose information to be printed to aid in debugging problems with the bridge chipset.
SEE ALSO
cardbus(4), exca(4), pccard(4)
BSD
July 21, 2004 BSD