Sponsored Content
Operating Systems AIX Trying to hookup my notebook to my IBM 7046-B50 type rack RS6000/AIX system Post 302181328 by dukessd on Wednesday 2nd of April 2008 04:09:37 PM
Old 04-02-2008
jgt, spooky, I never knew that.

Just fired up hyper-term on a pc with win2k and no serial ports and it asked for the ip address and shows default port 23!

Well I never!

Anyway, bakunin, sure does look like he is using ip not serial and as an aside I don't think IBM will sell you such a cable because they do not make one - or more correctly they do not know they sell one.

Well, not for connecting a 9 pin terminal to an rs6k, although I believe the ESS / Shark cable the CEs use for servicing the old 2105 is just the job, if only I knew the part number...

For PC to RS6k / pseries / system p connection using a 9 pin d-type at both ends the cable you need is as follows:

2 - 3
3 - 2
4 - 6 and 1
6 and 1 - 4
5 - 5
7 - 8
8 - 7

mhatmi, can you confirm if you are using IP or serial please.
Where are you plugging the cable into the B50?

Here are the books for your system:
pSeries and AIX Information Center

If you are using fixed IP on the B50 you will need to configure your laptop to use a fixed IP address in the same subnet as the B50 before the connection will work.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Installing PHP on IBM/RS6000 AIX UNIX

I am attempting to install PHP on an IBM RS6000 AIX UNIX box. I am not getting very far and hope someone can point me in the right direction. Here is the message from the output: checking for Apache 1.x module support via DSO through APXS Sorry I was not able to successfully run APXS.... (6 Replies)
Discussion started by: jyoung
6 Replies

2. AIX

PCI Ethernet Cards for IBM RISC 6000 - B50's

I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
Discussion started by: rahe
0 Replies

3. AIX

PCI Ethernet NIC's for IBM RISC 600 Model B50

I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies

4. AIX

New to AIX and got my hands on a RS6000 v.need help getting it on the network

So im fairly new to AIX and my knowledge is very, very limited but i got my hands on an RS6000 43P model and im trying to get it on the network so i can access it from work. I have pretty much tried everything i can/know how to do by reading up as much as i can but im still lost. I have the 43P... (2 Replies)
Discussion started by: IIIII
2 Replies

5. Debian

Red Hat, GNU/Linux, IBM RS6000?

All - I have a stack of RS6000's that need a Linux install - Red Hat 5.2 to be exact. Any tips/pointers on how to get this done without an HMC? I can get the discs to boot, but the install hangs when asking for user interaction - like pressing 'ENTER' to skip disc media check. Any help greatly... (4 Replies)
Discussion started by: b1f30
4 Replies

6. UNIX and Linux Applications

debian boot failed on IBM RS6000 7025 F80

Hi everybody. I have an old IBM RS6000 Model 7025 F80 with AIX 4.3.3 installed with 2 primary scsi disks. I want to install linux (any flavor) on it. I downloaded and burned an iso image of debian (http://cdimage.debian.org/debian-cd/4.0_r4a/powerpc/iso-cd/debian-40r4a-powerpc-netinst.iso),... (3 Replies)
Discussion started by: pitagoras
3 Replies

7. UNIX for Advanced & Expert Users

Using SCP command in IBM AIX to download file from remote to local system

Hi, When i run the code in solaris unix machine, the file from remote server is getting downloaded. but when i use the same code in IBM AIX remote machine, it is not running. It is saying "Erro during scp transfer." Below is the code. Please give some resolution. SCPClient client = new... (1 Reply)
Discussion started by: gravi2020
1 Replies

8. AIX

Reinstalling AIX 4.3 on IBM RS6000

Hey guys, I'm a newbie in Unix world.. Currently in my office lies an old IBM RS6000 which hasn't been maintained for a very long time. The former admin has resigned and we don't have any documentation or whatsoever regarding the old machine. All I know that it is an RS6000 is because of what's... (4 Replies)
Discussion started by: arch4ng3l
4 Replies

9. AIX

AIX 5.2 installation on 'IBM system p5 type 9110-51A'

Hi All, I am new to AIX, not completly though.. I got a task to install AIX 5.2 on 'IBM system p5 type 9110-51A' server. I tried few things, but i am not able to get to the console of this server to proceed with the installation. I have installed AIX 6.1 earlier, but those servers can be plugged... (4 Replies)
Discussion started by: nd007
4 Replies

10. AIX

AIX 5.1 and RS6000

I've an old server 1996 RS6000 (Processor 604e) running AIX 5.1. It started up fine, booted up and connected on 10Mbit with my router. I used to be able to connect to it with telnet but not anymore. I know the IP is right but working with the smit tcpip options, looks like I've changed... (1 Reply)
Discussion started by: Devyn
1 Replies
APCSMART(8)						      Network UPS Tools (NUT)						       APCSMART(8)

NAME
apcsmart - Driver for American Power Conversion Smart Protocol UPS equipment NOTE
This man page only documents the hardware-specific features of the apcsmart driver. For information about the core driver, see nutups- drv(8). SUPPORTED HARDWARE
apcsmart should recognize all APC models that use a serial protocol at 2400 bps. This is primarily the Smart-UPS and Matrix-UPS lines, but some Back-UPS Pro models are also supported. Some older hardware may only report a handful of variables. This is usually not a bug - they just don't support anything else. CABLING
This driver expects to see a 940-0024C cable or a clone by default. You can switch to the 940-0095B dual-mode cable support with the cable= definition described below. If your 940-0024C cable is broken or missing, use this diagram to build a clone: http://www.exploits.org/nut/library/cables/940-0024C.jpg EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5): cable=940-0095B Configure the serial port for the APC 940-0095B dual-mode cable. sdtype=num Use shutdown type num, according to this table: 0: soft shutdown or powerdown, depending on battery status 1: soft shutdown followed by powerdown 2: instant power off 3: power off with grace period Modes 0 and 1 will power up the load when power returns. Modes 2 and 3 will keep the load turned off when the power returns. BUGS
Some older APC UPS models return bogus data in the status register during a front panel test. This is usually detected and discarded, but some other unexpected values have occasionally slipped through. AUTHOR
Russell Kroll SEE ALSO
The core driver: nutupsdrv(8) Internet resources: The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/ NUT mailing list archives and information: http://lists.exploits.org/ Tue Oct 22 2002 APCSMART(8)
All times are GMT -4. The time now is 06:22 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy