03-31-2008
10 More Discussions You Might Find Interesting
1. Solaris
I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk.
The possible reason could be:
1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies
2. Filesystems, Disks and Memory
hi,
I have a SCO unix server which has a 36gb hard drive, but the IT company who supplied it assigned 1gb to /dev/root, 15mb to /dev/boot and 33gb to /dev/u.
The /dev/root partition is now full, is there a way I can use the 33gb assigned to /dev/u without loosing any data, preferably... (2 Replies)
Discussion started by: Martyn
2 Replies
3. UNIX for Advanced & Expert Users
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (5 Replies)
Discussion started by: kevindoman
5 Replies
4. UNIX for Dummies Questions & Answers
I have a FAT32 data disk attached to my Mac. It has 1 partition that is marked as bootable and the Mac tries to boot from it even though it has no OS on it. The man page for fdisk tells how to turn on the boot flag for a partition, but not how to remove it. Is there a way? Thanks! (0 Replies)
Discussion started by: jkorchok
0 Replies
5. Filesystems, Disks and Memory
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Discussion started by: builder88
1 Replies
6. Shell Programming and Scripting
Hi,
How can I run fdisk partition in a script without interactive input?
In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies
7. Red Hat
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies
8. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
9. UNIX for Advanced & Expert Users
Hello,
I have rebooted the RHEL VM but after rebooting the vm it not showing all the partition mounted on OS level, if i'll execute the fdisk -l command, then i'm able to see the same disk. below is the fdisk output :
# fdisk -l
Disk /dev/sda: 107.6 GB, 107639996416 bytes
255 heads, 63... (1 Reply)
Discussion started by: purushottamaher
1 Replies
10. Red Hat
Hi,
Please suggest steps to change grub from /dev/sda to /dev/sdb, (1 Reply)
Discussion started by: manoj.solaris
1 Replies