01-10-2008
Hi blowtorch,
Sorry for the late reply....
I have not tested it but form my research you can set the MAC address on the interfaces of a Sparc box. Here's what I dug up really quick with google:
How do I change a MAC address?
I figured since you can re-assign the MAC address via ifconfig and IPMP is configured with ifconfig that it may be possible.
10 More Discussions You Might Find Interesting
1. IP Networking
I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)
Discussion started by: kduffin
3 Replies
2. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
3. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
4. Solaris
Dear UNIX Gurus
I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it
Regards (4 Replies)
Discussion started by: girish.batra
4 Replies
5. Solaris
Hi friends ,
can anyone provide me the complete steps to configure IPMP in solaris 9 or 10 provided i have two NIC card ?
regards
jagan (4 Replies)
Discussion started by: jaganblore
4 Replies
6. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
7. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
8. Solaris
hi,
just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies
9. Solaris
hi all,
i start with solaris 11 and i am disapointed by the change on ip managing.
i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande
switch1
net0 aggregate1 |
net1 aggregate1 |-----|
|... (1 Reply)
Discussion started by: sylvain
1 Replies
10. Solaris
Hi all,
Just a few questions ->
Is an "OFFLINE" interface going back to "ONLINE" consider as a failback by IPMP ?
I have "FAILBACK=no" in my /etc/default/mpathd; however when i do the following
(igb0 and igb7 are in the same ipmp link based group)
q1) why does "if_mpadm -r igb7" cause... (0 Replies)
Discussion started by: javanoob
0 Replies
LEARN ABOUT DEBIAN
shorewall6-maclist
SHOREWALL6-MACLIST(5) [FIXME: manual] SHOREWALL6-MACLIST(5)
NAME
maclist - shorewall6 MAC Verification file
SYNOPSIS
/etc/shorewall6/maclist
DESCRIPTION
This file is used to define the MAC addresses and optionally their associated IPv6 addresses to be allowed to use the specified interface.
The feature is enabled by using the maclist option in the shorewall6-interfaces[1](5) or shorewall6-hosts[2](5) configuration file.
The columns in the file are as follows.
DISPOSITION - {ACCEPT|DROP|REJECT}[:log-level]
ACCEPT or DROP (if MACLIST_TABLE=filter in shorewall6.conf[3](5), then REJECT is also allowed). If specified, the log-level causes
packets matching the rule to be logged at that level.
INTERFACE - interface
Network interface to a host.
MAC - address
MAC address of the host -- you do not need to use the shorewall6 format for MAC addresses here. If IP ADDRESSESES is supplied then MAC
can be supplied as a dash (-)
IP ADDRESSES (Optional) - [address[,address]...]
If specified, both the MAC and IP address must match. This column can contain a comma-separated list of host and/or subnet addresses.
If your kernel and ip6tables have iprange match support then IP address ranges are also allowed. Similarly, if your kernel and
ip6tables include ipset support than set names (prefixed by "+") are also allowed.
FILES
/etc/shorewall6/maclist
SEE ALSO
http://shorewall.net/MAC_Validation.html
http://shorewall.net/configuration_file_basics.htm#Pairs
shorewall6(8), shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5), shorewall6-hosts(5), shorewall6-interfaces(5),
shoewall6-netmap(5),shorewall6-params(5), shorewall6-policy(5), shorewall6-providers(5), shorewall6-rtrules(5), shorewall6-routestopped(5),
shorewall6-rules(5), shorewall6.conf(5), shorewall6-secmarks(5), shorewall6-tcclasses(5), shorewall6-tcdevices(5), shorewall6-tcrules(5),
shorewall6-tos(5), shorewall6-tunnels(5), shorewall6-zones(5)
NOTES
1. shorewall6-interfaces
http://www.shorewall.net/manpages6/shorewall6-interfaces.html
2. shorewall6-hosts
http://www.shorewall.net/manpages6/shorewall6-hosts.html
3. shorewall6.conf
http://www.shorewall.net/manpages6/shorewall6.conf.html
[FIXME: source] 06/28/2012 SHOREWALL6-MACLIST(5)