first off, i am new to unix so please bear with me. i was reading somewhere that if your i-nodes get critical that it can slow your network down. what are i-nodes and when do they become a critical number? this is what mine states:
/ (/dev/root ): 777058 blocks 569290 i-nodes... (4 Replies)
Does anyone know something about this? I have no idea what it means and how to do it. but if anyone can give me and explanation and also point me to a website, i'd really appreciate it (5 Replies)
Hi,
I have created an empty file and a symbolic link to a file. But when I issue the following commands, I am getting the output 2.
stat -c "%s" linkfile
du -hb linkfile
Why this is happening? (4 Replies)
I am new to cluster commands. But I have tried utilizing: -pe, but I do not know my parallel computing environment. We are running SGE, is there a simpler command to request more nodes?
also: qsub -N auto -M name@email.com -m abe auto.sh
does not email me at all.
Help would be appreciated (0 Replies)
Hi,
I am new in system administration. I observe that some nodes in our cluster
are not considered as active by showq:
22 active jobs 217 of 257 processors in use by local jobs (84.44%)
15 of 17 nodes active (88.24%)
but then I try to log into... (1 Reply)
Hi
i have folder of 26 GB on server A and want to copy to server B .i used the below commands to check file size and scp copy
du -h /folder : its shows 26G on server A
from server B:
scp -r user@serverA:/folder/* ./copying got initiated and i am checking the file size on server B... (7 Replies)
Hi all. I have two nodes taken different places. They are connected together on a network. So, i have a service, it works on one of nodes and when the node is unavailable the service should will be launched on other node.
Solution: rhel cluster, keepalive, hearbeat...may be Carp
but what if... (2 Replies)
Hi all,
I have a list of node pairs separated with a comma and also, associated with their respective values. For example:
b0015,b1224 1.1
b0015,b2576 1.4
b0015,b3162 2.5
b0528,b1086 1.7
b0528,b1269 5.4
b0528,b3602 2.1
b0948,b2581 3.2
b1224,b0015 1.1... (8 Replies)
Hi folks.
I've been a developer for far too many years, but know very little of unix. I have setup a very inexpensive cluster of 6 raspberry pi nodes so I can play around with multi node programming. This is only for fun, but I want to learn properly, else what's the point?!
Setup can be a... (4 Replies)
Discussion started by: MuntyScrunt
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)