07-19-2007
maybe you should run a "sys-unconfig" and start with a fresh config... if that is not possible, check the files for typos and also check /etc/hostname.interfacename and /etc/nodename.
btw. there is no need for rsc and the other interface to be in one vlan!
10 More Discussions You Might Find Interesting
1. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
2. AIX
I've got an RS6K B50, and i've installed AIX 5.3, TL5. It installs fine, the only customisations i make to the BOS are to change the locale / keyboard layout to UK, and to choose not to install graphical software.
I have no video card in this box, and i connect via a serial console (null modem... (4 Replies)
Discussion started by: craigp84
4 Replies
3. AIX
Hi guys,
Got a tiny bit of a problem on one of our servers here at work. I installed AIX 5.3 on the server and that went fine. Then I upgraded to ML 5300-05-01, but now the system just hangs on boot.
The system starts up and the monitor comes on in few minutes, but a few seconds later when... (6 Replies)
Discussion started by: drchris
6 Replies
4. AIX
To All:
I have this AIX machine (see boot process below). The problem was it hangs at:
The ctrmc Subsystem has been started. Subsystem PID is 11906..
I checked with other forums but their advise were just "strong punches in the air" with no specific explanation.
I really appreciate if... (6 Replies)
Discussion started by: aix_xia
6 Replies
5. Ubuntu
Boot process hangs after reaching the following line:
Adding 5853176k swap on /dev/mapper/mch-swap_1. Priority:-1 extents:1 across:5853176kUsing knoppix 6.2 as LiveCD, and mounting the partitions, I got the following:
# /etc/fstab: static file system information.
#
# Use 'blkid -o value -s... (0 Replies)
Discussion started by: fzaker
0 Replies
6. AIX
Hi all,
We have a old Power4 server with AIX version 5.3 installed. Upon boot up, it hangs right after the AIX welcome screen. On the diagnostic load progress LED indicator, I saw that it stopped at '0c32' then after awhile the LED would be blank. The screen on the monitor will hang at the black... (15 Replies)
Discussion started by: a_sim
15 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server... (1 Reply)
Discussion started by: ccj4467
1 Replies
9. Solaris
Hi Guys,
I have a SunBlade 1500 which I use to practice at home. Suddenly when I power on the server it just displays the solaris banner and Boot device: disk File and args: Then it stops and says " rebooting with command: boot"
It doesn't boot to the kernel. Is there anyway I can possibly... (5 Replies)
Discussion started by: cjashu
5 Replies
10. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
LEARN ABOUT BSD
sys-unconfig
sys-unconfig(1M) System Administration Commands sys-unconfig(1M)
NAME
sys-unconfig - undo a system's configuration
SYNOPSIS
/usr/sbin/sys-unconfig
DESCRIPTION
The sys-unconfig command is used to restore a system's configuration to an "as-manufactured" state, ready to be reconfigured again. The
system's configuration consists of hostname, Network Information Service (NIS) domain name, timezone, IP address, IP subnet mask, and root
password. This operation is the inverse of those performed by the sysidnet(1M), sysidns(1M), and sysidsys(1M) programs run at boot. See
sysidtool(1M).
sys-unconfig does the following:
o Saves current /etc/inet/hosts file information in /etc/inet/hosts.saved.
o If the current /etc/vfstab file contains NFS mount entries, saves the /etc/vfstab file to /etc/vfstab.orig.
o Restores the default /etc/inet/hosts file.
o Removes the default hostname in /etc/hostname.interface files for all interfaces configured when this command is run. To determine
which interfaces are configured, run the command 'ifconfig-a'. The /etc/hostname.interface files corresponding to all of the inter-
faces listed in the resulting output, with the exception of the loopback interface (lo0), will be removed.
o Removes the default domainname in /etc/defaultdomain.
o Restores the timezone to PST8PDT in /etc/TIMEZONE.
o Disables the Network Information Service (NIS) and Network Information Service Plus (NIS+) if either NIS or NIS+ was configured.
o Removes the file /etc/inet/netmasks.
o Removes the file /etc/defaultrouter.
o Removes the password set for root in /etc/shadow.
o Removes the file /etc/.rootkey.
o Executes all system configuration applications. These applications are defined by prior executions of a sysidconfig -a application.
(See sysidconfig(1M)). When sys-unconfig is run, all system configuration applications are passed one argument, -u.
o Removes the file /etc/resolv.conf.
o Disables LDAP by removing /var/ldap/ldap_client_cache, /var/ldap/ldap_client_file, /var/ldap/ldap_client_cred, and
/var/ldap/cachemgr.log.
o Regenerates keys for sshd(1M).
When sys-unconfig is finished, it performs a system shutdown. sys-unconfig is a potentially dangerous utility and can only be run by the
super user.
FILES
/etc/default/init process control initialization
/etc/defaultdomain
/etc/defaultrouter
/etc/hostname.interface
/etc/inet/hosts host name database
/etc/inet/netmasks network mask database
/etc/nodename
/etc/.rootkey super-user's secret key
/etc/shadow shadow password file
/etc/vfstab virtual file system table
/var/nis/NIS_COLD_START
/var/yp/binding/*/ypservers
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWadmap |
+-----------------------------+-----------------------------+
SEE ALSO
init(1M), kdmconfig(1M), sshd(1M), sysidconfig(1M), sysidtool(1M), hosts(4), netmasks(4), shadow(4), attributes(5)
NOTES
sys-unconfig is not available on diskless clients.
SunOS 5.10 4 Jun 2004 sys-unconfig(1M)