qmail-remote(8) 					      System Manager's Manual						   qmail-remote(8)

NAME

       qmail-remote - send mail via SMTP

SYNOPSIS

       qmail-remote host sender recip [ recip ...  ]

DESCRIPTION

       qmail-remote reads a mail message from its input and sends the message to one or more recipients at a remote host.

       The  remote host is qmail-remote's first argument, host.  qmail-remote sends the message to host, or to a mail exchanger for host listed in
       the Domain Name System, via the Simple Mail Transfer Protocol (SMTP).  host can be either a fully-qualified domain name:

	    silverton.berkeley.edu

       or an IP address enclosed in brackets:

	    [128.32.183.163]

       The envelope recipient addresses are listed as recip arguments to qmail-remote.	The envelope sender address is listed as sender.

       Note that qmail-remote does not take options and does not follow the getopt standard.

TRANSPARENCY

       End-of-file in SMTP is encoded as dot CR LF.  A dot at the beginning of a line is encoded as dot dot.  It is impossible in SMTP to  send  a
       message	that does not end with a newline.  qmail-remote converts the UNIX newline convention into the SMTP newline convention by inserting
       CR before each LF.

       It is a violation of the SMTP protocol to send a message that contains long lines or non-ASCII characters.  However, qmail-remote will hap-
       pily send such messages.  It is the user's responsibility to avoid generating illegal messages.

RESULTS

       qmail-remote  prints  some  number of recipient reports, followed by a message report.  Each report is terminated by a 0 byte.  Each report
       begins with a single letter:

       r    Recipient report: acceptance.

       h    Recipient report: permanent rejection.

       s    Recipient report: temporary rejection.

       K    Message report: success.  host has taken responsibility for delivering the message to each acceptable recipient.

       Z    Message report: temporary failure.

       D    Message report: permanent failure.

       After this letter comes a human-readable description of what happened.

       The recipient reports will always be printed in the same order as qmail-remote's recip arguments.  Note that in failure cases there may	be
       fewer recipient reports than recip arguments.

       qmail-remote always exits zero.

CONTROL FILES

       helohost
	    Current host name, for use solely in saying hello to the remote SMTP server.  Default: me, if that is supplied; otherwise qmail-remote
	    refuses to run.

       smtproutes
	    Artificial SMTP routes.  Each route has the form domain:relay, without any extra spaces.  If domain matches  host,	qmail-remote  will
	    connect  to  relay,  as  if host had relay as its only MX.	(It will also avoid doing any CNAME lookups on recip.)	host may include a
	    colon and a port number to use instead of the normal SMTP port, 25:

	       inside.af.mil:firewall.af.mil:26

	    relay may be empty; this tells qmail-remote to look up MX records as usual.  smtproutes may include wildcards:

	       .af.mil:
	       :heaven.af.mil

	    Here any address ending with .af.mil (but not af.mil itself) is routed by its MX records; any other address is artificially routed	to
	    heaven.af.mil.

	    The qmail system does not protect you if you create an artificial mail loop between machines.  However, you are always safe using smt-
	    proutes if you do not accept mail from the network.

       timeoutconnect
	    Number of seconds qmail-remote will wait for the remote SMTP server to accept a connection.  Default: 60.  The kernel normally imposes
	    a 75-second upper limit.

       timeoutremote
	    Number of seconds qmail-remote will wait for each response from the remote SMTP server.  Default: 1200.

SEE ALSO

       addresses(5), envelopes(5), qmail-control(5), qmail-send(8), qmail-smtpd(8), qmail-tcpok(8), qmail-tcpto(8)

																   qmail-remote(8)