Visit The New, Modern Unix Linux Community

Operating Systems Solaris check firmaware revision on X4100 Post 302098415 by hcclnoodles on Monday 4th of December 2006 05:15:42 AM
check firmaware revision on X4100

Hi there

I am running solaris 10 on an SunFire x4100 ...(x86 box) Could anybody tell me if there is a way I can check the firmware revision without taking the box down to do it ...eeprom doesnt give me the info I require

Test Your Knowledge in Computers #676
Difficulty: Medium
The first version of the 802.11 protocol was released in 1997, and provided up to 12 MB/s link speeds.
True or False?

10 More Discussions You Might Find Interesting

1. Solaris

X4100 Bios RAID question

Hi there the Sunfire X4100 has a great tool that you can get to from BIOS called the configuration utility which allows you to set up Disk mirroring (RAID 1) before the OS sees it, which is great and it works a treat, however, we have a large datacentre across multiuple sites and I need to find... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

2. Solaris

ILOM Configuration in Galaxy x4100 server

Hai All I rquire a small help for Galaxy x4100 server, when we are trying to sepup ILOM through CLI it gives following error on commitpending=true steps. set pendingipaddress= Set 'pendingipaddress' to '' -> set pendingipgateway= Set... (1 Reply)
Discussion started by: sure.solaris
1 Replies

3. Solaris

How to change boot slot X4100?

Hi everyone, I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1. When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies

4. Programming

Revision Control Sw

Hi All, Please let me know any freeware revision control software name and URL. Any response is highly appreciated. OS: Solaris 5.10 Thanks, Naga:cool: (3 Replies)
Discussion started by: Nagapandi
3 Replies

5. Solaris

Does the Sun fire x4100 support HVM?

I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies

6. Hardware

sun x4100 M2 processors

hi please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition. thanks (2 Replies)
Discussion started by: bahjatm
2 Replies

7. Hardware

Sun X4100 graphics

Hello all. I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots. thanks (4 Replies)
Discussion started by: petebarchetta
4 Replies

8. Hardware

How to identify virtual/physic disk path on X4100?

Hello, Currently we have a Oracle X4100 ( Solaris 10 ) server with disk failure. Originally our hardware team thought the disk can be hot-swap, when they stood in front of the server, none of the disk failure LED were on, so now we have no idea which disk is the bad one for replacement. As... (2 Replies)
Discussion started by: sunnychen98
2 Replies

9. Ubuntu

Ubuntu Install on Sun Fire X4100 network issues

Hi I have two Sun Fire X4100 machines with Ubuntu 12.04 installed on them. I am able to configure the Net Mgt port with an IP address and access the ILOM from the browser. I can also boot the Ubuntu installed and redirect the output. The issue i have is that when i configure the network... (0 Replies)
Discussion started by: kaf3773
0 Replies

10. Solaris

Sunfire X4100 server

Hi, I am currently on Sunfire X4100. This server doesn't have CDROM drive. Also I can't get to the OK prompt. From my laptop, I am connected to the management port using the Cisco Blue cable. Please advise how can I get to the OK prompt. Also the server is so loud. Will the FAN cool... (1 Reply)
Discussion started by: samnyc
1 Replies
glutButtonBoxFunc(3GLUT)					       GLUT						  glutButtonBoxFunc(3GLUT)

glutButtonBoxFunc - sets the dial & button box button callback for the current window. SYNTAX
#include <GLUT/glut.h> void glutButtonBoxFunc(void (*func)(int button, int state)); ARGUMENTS
func The new button box callback function. DESCRIPTION
glutButtonBoxFunc sets the dial & button box button callback for the current window. The dial & button box button callback for a window is called when the window has dial & button box input focus (normally, when the mouse is in the window) and the user generates dial & button box button presses. The button parameter will be the button number (starting at one). The number of available dial & button box buttons can be determined with glutDeviceGet(GLUT_NUM_BUTTON_BOX_BUTTONS). The state is either GLUT_UP or GLUT_DOWN indicating whether the callback was due to a release or press respectively. Registering a dial & button box button callback when a dial & button box device is not available is ineffectual and not an error. In this case, no dial & button box button callbacks will be generated. Passing NULL to glutButtonBoxFunc disables the generation of dial & button box button callbacks. When a new window is created, no dial & button box button callback is initially registered. SEE ALSO
glutDialsFunc, glutDeviceGet, glutSpaceballButtonFunc, glutTabletButtonFunc AUTHOR
Mark J. Kilgard ( GLUT
3.7 glutButtonBoxFunc(3GLUT)

Featured Tech Videos

All times are GMT -4. The time now is 04:07 PM.
Unix & Linux Forums Content Copyright 1993-2020. All Rights Reserved.
Privacy Policy