10-17-2002
Take a look at the Software RAID howto for lots of useful information.
http://www.tldp.org/HOWTO/Software-RAID-HOWTO.html
But basically Raid-0 is no better, reliability wise, than a single harddrive. It just provides better performance because it is writing to multiple drives.
Level 1 mirrors between the drives so that when one finally fails the data is still on the other drive(s).
bcl
9 More Discussions You Might Find Interesting
1. Solaris
hai everybody n good morning........here r some queries.......
1. what is the interlace value in RAID 0 (striping.......)
2. How many no of metadevices are required for mirroring and why......... (1 Reply)
Discussion started by: sudhansu
1 Replies
2. Solaris
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Discussion started by: sudhansu
3 Replies
3. Solaris
Somebody can help me ! how can i do mirror in sun ver 8
without third party software !!! (3 Replies)
Discussion started by: goldfelda
3 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
6. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LINUX(4) BSD Kernel Interfaces Manual LINUX(4)
NAME
linux -- Linux ABI support
SYNOPSIS
To compile support for this ABI into an i386 kernel place the following line in your kernel configuration file:
options COMPAT_LINUX
for an amd64 kernel use:
options COMPAT_LINUX32
Alternatively, to load the ABI as a module at boot time, place the following line in loader.conf(5):
linux_load="YES"
DESCRIPTION
The linux module provides limited Linux ABI (application binary interface) compatibility for userland applications. The module provides the
following significant facilities:
o An image activator for correctly branded elf(5) executable images
o Special signal handling for activated images
o Linux to native system call translation
It is important to note that the Linux ABI support it not provided through an emulator. Rather, a true (albeit limited) ABI implementation
is provided.
The following sysctl(8) tunable variables are available:
compat.linux.osname Linux kernel operating system name.
compat.linux.osrelease Linux kernel operating system release. Changing this to something else is discouraged on non-development systems,
because it may change the way Linux programs work. Recent versions of GNU libc are known to use different syscalls
depending on the value of this sysctl.
compat.linux.oss_version Linux Open Sound System version.
The linux module can be linked into the kernel statically with the COMPAT_LINUX kernel configuration option or loaded as required. The fol-
lowing command will load the module if it is neither linked into the kernel nor already loaded as a module:
if ! kldstat -v | grep -E 'linux(aout|elf)' > /dev/null; then
kldload linux > /dev/null 2>&1
fi
Note that dynamically linked Linux executables will require a suitable environment in /compat/linux. Specifically, the Linux run-time
linker's hints files should be correctly initialized. For this reason, it is common to execute the following commands to prepare the system
to correctly run Linux executables:
if [ -x /compat/linux/sbin/ldconfig ]; then
/compat/linux/sbin/ldconfig -r /compat/linux
fi
For information on loading the linux kernel loadable module automatically on system startup, see rc.conf(5). This information applies
regardless of whether the linux module is statically linked into the kernel or loaded as a module.
FILES
/compat/linux minimal Linux run-time environment
/compat/linux/proc limited Linux process file system
/compat/linux/sys limited Linux system file system
SEE ALSO
brandelf(1), elf(5), linprocfs(5), linsysfs(5)
HISTORY
Linux ABI support first appeared in FreeBSD 2.1.
BSD February 8, 2010 BSD