06-05-2001
Network Interface
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt
10 More Discussions You Might Find Interesting
1. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
2. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
3. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
TXP(4) BSD Kernel Interfaces Manual TXP(4)
NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)
HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD
March 12, 2009 BSD