08-20-2002
At a former employer, we just used Xyplex PAD's. When they got a X.25 connection, they would just open a telnet session to a unix host. Our unix hosts never knew about X.25. I think that other companies besides Xyplex have PAD's with this ability.
10 More Discussions You Might Find Interesting
1. Cybersecurity
!HELLO ,
What is the maximum number of hosts on a TCP/IP internet?
plz can u help me.
:rolleyes: (2 Replies)
Discussion started by: smdakram
2 Replies
2. IP Networking
Here's my config: One quadra 840av working under netBSD and successfully connected to my network. One PM 6100 connected but not booting fully into netBSD (i realize this is faulty but I figured it was worth a shot to try and install netBSD/mac68k on it due to the fact it is unsupported under the... (1 Reply)
Discussion started by: Yummator
1 Replies
3. Programming
i am programming a tcp_ip server which intends to listen permanently to a client . the client can disconnect and connect again and the server accept it(by this point it works).The problem is when the client lose connection without a disconnect command and my code can't get it and keeps waiting for... (4 Replies)
Discussion started by: massimo_ratti
4 Replies
4. SCO
How can I change timers for TCP/IP sockets in SCO Unix 7.1.1:o (1 Reply)
Discussion started by: Dragan Travica
1 Replies
5. IP Networking
I have written a TCP/IP client and server program. The client sends a message to the server and then the server sends a file back to the client. The client reads the buffer and stores it another file in the client side.
I need to know what are the various exceptions that I need to handle in... (0 Replies)
Discussion started by: Rajeshsu
0 Replies
6. AIX
Hi,
Is there anyway to bring down ethernet interface using non-root ID?
Appreciate if you could advice how to do that using non-root ID and what are previleges required in order to perform the tasks.
Thanks (1 Reply)
Discussion started by: srllee
1 Replies
7. Solaris
I am running a Java Client on Solaris 9 which communicates with the Server using TCP/IP.
The client transmits a FIN packet to server. The server sends a ACK, FIN enters LAST_ACK state and then waits for ACK from client. The client did not respond back leaving the server in LAST_ACK itself. Also... (0 Replies)
Discussion started by: diarun
0 Replies
8. Programming
Hi guys.
I'm going to buy TCP/IP Illustrated series(3 Volumes). But I saw that these books are very outdated. But reviews at amazon says that these books are awesome.
What is your idea? Is it worth? What else do you suggest?
I'm interested in practical books from protocol design to... (1 Reply)
Discussion started by: majid.merkava
1 Replies
9. IP Networking
Hello all,
Can somebody please tell what is the best book out there that can help me learn TCP troubleshooting and understaning the TCP options like window scaling, large receive offload? I would like to understand how all the TCP tuning parameters function. Is there a book out there that can... (4 Replies)
Discussion started by: Pouchie1
4 Replies
10. Solaris
I have problem with oracle solaris 10 running on oracle sparc T4-2 server.
Os information: 5.10 Generic_150400-03 sun4v sparc sun4v
Output from tcpstat.d script
TCP bytes: out outRetrans in inDup inUnorder
6833763 7300 98884 0... (2 Replies)
Discussion started by: insatiable1610
2 Replies
LEARN ABOUT CENTOS
telnet-probe
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)
NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO
PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)