06-17-2002
Memory problem
Hi:
I have a server with a very little memory leak (29 bytes) as reported by Purify.
Itīs a pooled server, so each process lives forever accepting conections.But top or ps commands show that used memory it is always increasing much more than 29 bytes (30K mor or less) in each conection.
How can this be if Purify reports such a little memory leak?
10 More Discussions You Might Find Interesting
1. Programming
Hi ,
One of java programs in our machine allocates 256M of heap memory and max of 512 memory(Tomcat to be specific).
Our ulimit per process is 32M.How can a process allocates such a big amount of memory
ps v output is
PGIN SIZE RSS LIM TSIZ TRS %CPU %MEM COMMAND
... (0 Replies)
Discussion started by: ganti
0 Replies
2. Filesystems, Disks and Memory
Hi ,
One of java programs in our machine allocates 256M of heap memory and max of 512 memory(Tomcat to be specific).
Our ulimit per process is 32M.How can a process allocates such a big amount of memory
ps v output is
PGIN SIZE RSS LIM TSIZ TRS %CPU %MEM COMMAND
24 220776 220892... (0 Replies)
Discussion started by: ganti
0 Replies
3. Programming
Hi, I try to marshal a unsigned int and a char * into a buffer, and then unmarshal them later to get them out. I need to put the char * in the front and unsigned int at the end of the buffer. However, my system always give me "BUS ERROR". I am using Sun Sparcs Sloris 2.10.
My code to marshal... (6 Replies)
Discussion started by: nj302
6 Replies
4. Solaris
i am building open source software on a solaris 8 machine
for couple of days i am getting error messages like
out of memory
or
no more processes and then build is failing
i tried with rebooting the machine but then after couple of days same problem is arising again.
can any one... (1 Reply)
Discussion started by: mobydick
1 Replies
5. Shell Programming and Scripting
how the data from disk is loaded into memory and then it supplied to tcp/ip packet.
how i can trace the no of pages loaded in memory by that process and rate of context switch for that process. (1 Reply)
Discussion started by: amar20
1 Replies
6. Programming
I have a program that will fetch some particular lines and store it in a buffer for further operations.The code which is given below works but with some errors.I couldn't trace out the error.Can anybody help on this plz??
#include <stdio.h>
#include <stdlib.h>
#include<string.h>
#define... (1 Reply)
Discussion started by: vigneshinbox
1 Replies
7. Programming
hi all
Can any one plz explain me about memory leak problem
Thankx (5 Replies)
Discussion started by: sonali
5 Replies
8. HP-UX
Hi,
This is my 1st post here. I am facing a rather weired problem. I have a C++ binary running on HP-UX. The output of top as well as glance shows periodic increase in memory. But when i use gdb to detect it, i dont get the desired output...gdb says...no leaks found. Just to mention that I have... (2 Replies)
Discussion started by: kshk123
2 Replies
9. Red Hat
Hi, I have a Linux distribution ( Oralce Enterprise Linux 5.3 i.e. Redhat ) that I have installed. It works fine when I used 2*512Mb dimms or replace them with a single 1Gb dimm. However when I try to go above 1 Gb the bootup and general performance deteriorates badly. The BIOS picks up the memory... (3 Replies)
Discussion started by: jimthompson
3 Replies
10. UNIX for Dummies Questions & Answers
I am using ubuntu. I have written a program to calculate prime factors. it works perfectly fine till entered number is less than 9989 (or so ) but when one enters a number higher than that, for example 15000, it does not work. Can anyone guide me whats the problem ? although new codes are welcome,... (2 Replies)
Discussion started by: Abhishek_kumar
2 Replies
LEARN ABOUT DEBIAN
build-lives-rfx-plugin
build-lives-rfx-plugin(1) General Commands Manual build-lives-rfx-plugin(1)
NAME
build-lives-rfx-plugin - builds rendered effects for LiVES
SYNOPSIS
build-lives-rfx-plugin script_name [plugin_dir] -get section file
DESCRIPTION
This perl script is used by LiVES to compile an RFX (rendered effect) plugin for LiVES. It is generally called from build-lives-rfx-plugin-
multi for a script which has a language code representing LiVES-perl. The script_name must be the full (absolute) path to the plugin
script, and plugin_dir can be used to specify the output directory where the compiled plugin should be generated. If plugin_dir is not
defined then /tmp is assumed.
The second variant with -get is used to print out a script section from a plugin script to stdout. It is generally only used internally by
LiVES.
Return values The script returns the following values
0 - success 1 - the value of a trigger was greater than the number of parameters 2 - a value could not be read from the script file 3 - the
language code of the plugin script was not equivalent to LiVES-perl 4 - the API version level of the plugin script was invalid 5 - the
<define> section was missing from the plugin script
SEE ALSO
build-lives-rfx-plugin-multi(1), lives(1)
AUTHOR
Gabriel Finch a.k.a Salsaman (salsaman@xs4all.nl)
May 9 2010 build-lives-rfx-plugin(1)