Sponsored Content
Full Discussion: SWAP SPACE
Top Forums UNIX for Dummies Questions & Answers SWAP SPACE Post 195 by SmartJuniorUnix on Wednesday 8th of November 2000 10:37:09 AM
Old 11-08-2000
Question

All,
I am using SOLARIS 7. I have formated my hard drive to consist of only 150MB of swap space. This isn't enough considering I am running Oracle. How do I create additional swap space?
Please list sources or commands.

PS mkswap doesn't work on my machine. ( I have swap and swapadd)

Thanks a bunch
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

pageing space vs swap space

Hello, I would like to know if there is any difference between the pageing space and the swap space. Thank you in advance. (1 Reply)
Discussion started by: VeroL
1 Replies

2. UNIX for Dummies Questions & Answers

Swap space is LOW

I checked the server and issued various command to investigated. but from teh output of swap -s and swap -l, i received the following swap -l swapfile dev swaplo blocks free /dev/vx/dsk/swapvol 197,7 16 4194800 4127696 /dev/vx/dsk/swap2 197,8 16 12582896... (3 Replies)
Discussion started by: TRUEST
3 Replies

3. AIX

swap space / paging space

how do you get the paging space reduced without rebooting the machine ? the os is aix (2 Replies)
Discussion started by: aaronh
2 Replies

4. UNIX for Dummies Questions & Answers

Swap space used???

Plz I need to know how much swap mem free and used i have. I'm using Compaq Tru64 UNIX V5.1A (rev 1885) Thanx (1 Reply)
Discussion started by: Lestat
1 Replies

5. Linux

swap space

Hi, I want to know how can i free the swap space if it is completely full, 0 mb remaining, (1 Reply)
Discussion started by: manoj.solaris
1 Replies

6. Solaris

Swap Space

Could someone please explain how you know how much swap space you have on your system. See below: # swap -s total: 8225048k bytes allocated + 4863488k reserved = 13088536k used, 4008032k available # swap -l swapfile dev swaplo blocks free /dev/dsk/c3t0d0s1 32,25 16... (2 Replies)
Discussion started by: jamba1
2 Replies

7. Linux

How to reclaim the space which i used to increse the swap space on Xen,

Hi, i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :- 1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024 1057 ls -l /root/myswapfile 1058 chmod 600 /root/myswapfile 1059 mkswap /root/myswapfile 1060 swapon /root/myswapfile ... (1 Reply)
Discussion started by: apm
1 Replies

8. Solaris

Swap space

Dear All, I have a swap space of 16G available in Sol 10. I have allocated it as a seperate file system. But when the RAM Is full used , the system gets rebooted and the swap is not being used,. Any reasons for this. Rgds Rj (5 Replies)
Discussion started by: jegaraman
5 Replies

9. Red Hat

Swap space not getting used

CENT OS 5.8 server running with a huge java application which uses up all my ram (4GB) and requires excess of atleast 2GB.But the swap is not getting used up((8GB) of swap space left unused) leading a wierd error and stopping application to stop working. Any one here dealt with the same kind of... (2 Replies)
Discussion started by: shiek.kaleem
2 Replies

10. Red Hat

Extending swap space

I've to install Oracle binaries (I'm oracle DBA) and for that I've extend swap space in my home computer. My situation is like this. # parted -s /dev/sda print free Model: ATA VBOX HARDDISK (scsi) Disk /dev/sda: 38.7GB Sector size (logical/physical): 512B/512B Partition Table: msdos ... (1 Reply)
Discussion started by: Mukul Sharma
1 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 06:43 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy