03-15-2001
You might just be able to swap the cards without any changes to the kernel. This is true is the model number of the cards are the same or if the basic chipsets are the same.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
7. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
8. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT SUSE
vga_setchipset
vga_setchipset(3) Svgalib User Manual vga_setchipset(3)
NAME
vga_setchipset - force chipset
SYNOPSIS
#include <vga.h>
void vga_setchipset(int chipset);
DESCRIPTION
Force detection of a chipset (when chipset detection fails). vga_setchipset(VGA) can be useful if the chipset specific stuff or the SVGA
detection stuff gives problems.
However, at first the automatic detection should work well, and if not a specific chipset can be forced from /etc/vga/libvga.config.
Because of that, void vga_setchipset(int chipset) should probably never be used by applications. If used nevertheless, it should be called
directly before vga_init(3).
As of now the following values are defined for chipset:
UNDEFINED
This is the default and specifies autodetection.
VGA A plain VGA card, not that the SVGA must behave like an ordinary SVGA card then which will probably mean it is in an ordinary
(25x80) textmode.
ET4000 Tseng ET4000/ET4000W32(i/p) cards.
CIRRUS Cirrus Logic GD542x/3x cards.
TVGA8900
Trident TVGA 8900C/9000 (and possibly also 8800CS/8900A/B) cards.
OAK Oak Technologies OTI-037/67/77/87 cards.
EGA An ordinary EGA card. The notes about VGA apply.
S3 An S3 base card.
ET3000 Tseng ET3000 cards.
MACH32 A card (from ATI or not) based on the ATI Mach32 chipset.
GVGA6400
A Genoa(?) GVGA6400 card.
ARK ARK Logic ARK1000PV/2000PV cards.
ATI An ATI SVGA (VGA Wonder and friends) card. This does not (necessarily) include the newer cards (usually called Mach something).
ALI An ALI2301 based card.
MACH64 A card using the ATI Mach64 chipset. Support is not complete.
CHIPS Chips and Technologies chipsets 65525, 65535, 65546, 65548, 65550, and 65554 (usually in laptops).
SEE ALSO
svgalib(7), vgagl(7), libvga.config(5), vgatest(6), vga_getcurrentchipset(3), vga_setchipsetandfeatures(3)
AUTHOR
This manual page was edited by Michael Weller <eowmob@exp-math.uni-essen.de>. The exact source of the referenced function as well as of the
original documentation is unknown.
It is very likely that both are at least to some extent are due to Harm Hanemaayer <H.Hanemaayer@inter.nl.net>.
Occasionally this might be wrong. I hereby asked to be excused by the original author and will happily accept any additions or corrections
to this first version of the svgalib manual.
Svgalib (>= 1.2.11) 27 July 1997 vga_setchipset(3)