can't get my cable modem up Post: 11179

10 More Discussions You Might Find Interesting

1. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that...

2. UNIX for Dummies Questions & Answers

Linux and my cable modem

I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now?

3. UNIX for Dummies Questions & Answers

Is anyone using unix with cable modem

Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how. Thank you for all your help.

4. UNIX for Advanced & Expert Users

Terminal 'Local Echo' lost on Modem Dial-out

Can anybody help me? I am developing a utility for automating message paging to a BT alphanumeric pager. I am using a USR 56K Fax-modem connected to /dev/cuab on a Sun Ultra-10. I am using the UNIX 'tip' utility to connect to the modem and I have configured the modem as follows: Baud Rate:...

5. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how...

6. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how...

7. UNIX for Dummies Questions & Answers

Installing Cable Modem on Irix Machine.

Ok I am new to this and wondering if there is any way of connecting a cable modem to an SGI that is running IRIX 6.5 and how to do it...

8. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created...

9. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks

10. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet...

LEARN ABOUT DEBIAN

ex

EX(4)							 BSD/i386 Kernel Interfaces Manual						     EX(4)

NAME

     ex -- Ethernet device driver for the Intel EtherExpress Pro/10 and Pro/10+

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device ex

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_ex_load="YES"

DESCRIPTION

     The ex driver provides support for Ethernet adapters based on the Intel i82595 chip.

     On the ISA bus, the card will be searched for in the I/O address range 0x200 - 0x3a0.  The IRQ will be read from the EEPROM on the card.  For
     correct operation Plug-N-Play support should be disabled.

     On the PC Card bus, the card will be automatically recognized and configured.

HARDWARE

     The ex driver supports the following Ethernet adapters:

     o	 Intel EtherExpress Pro/10 ISA
     o	 Intel EtherExpress Pro/10+ ISA
     o	 Olicom OC2220 Ethernet PC Card
     o	 Olicom OC2232 Ethernet/Modem PC Card
     o	 Silicom Ethernet LAN PC Card
     o	 Silicom EtherSerial LAN PC Card

DIAGNOSTICS

     ex%d: Intel EtherExpress Pro/10, address %6D, connector %s  The device probe found an installed card, and was able to correctly install the
     device driver.

     ex%d: WARNING: board's EEPROM is configured for IRQ %d, using %d  The device probe detected that the board is configured for a different
     interrupt than the one specified in the kernel configuration file.

     ex%d: invalid IRQ.  The device probe detected an invalid IRQ setting.

SEE ALSO

     arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The ex device driver first appeared in FreeBSD 2.2.

AUTHORS

     The ex device driver was written by Javier Martin Rueda.  The PC Card attachment was written by Mitsuru ISAWAKI and Warner Losh.  This manual
     page was written by David E. O'Brien.

BUGS

     Currently the driver does not support multicast.

     The Silicom EtherSerial card's serial port does not currently work.  The Olicom OC2232 PC Card should work with the ex driver, but is cur-
     rently completely broken.

BSD
								   July 16, 2005							       BSD