SCO openserver 6 parallel port issues


 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers SCO openserver 6 parallel port issues
# 1  
Old 06-29-2006
SCO openserver 6 parallel port issues

I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be there. I also attempted using mkdev but because its 6 its supposed to set itself up. I am running the same software on another computer and it works fine the only diffrence is the system I am using know is an ISA board this might also affect it but I don't know. Is there a way to configure the port to recognize the dongle? If anyone can offer any assistance I would be very greatful Thankyou.
 
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

2. UNIX for Dummies Questions & Answers

Parallel port Printing in SCO OSR6

Hi, I am trying to add a parallel printer to my SCO OSR6 server, yet when I run mkdev parallel it just brings up the message: "Parallel Ports are configured automatically in SCO Openserver 6". So when I try and add a local printer, no /dev/lp# ports are shown in the list, only serial ports... (1 Reply)
Discussion started by: Martyn
1 Replies

3. SCO

PCI Express 1x HBA for parallel SCSI in Openserver 6

I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies

4. SCO

PCI / PCIExpress Parallel port in SCO 6.0.0

How do or what do I need to add PCI / PCIe (PCI Express) parallel ports add-on adapters to OpenServer 6.0.0? OpenServer 5 could see PCI slots but OpenServer 6.0.0 (Original CD or the Re-cut one) required a maintenance pack to be installed? Is this right and how do I check to see if these work? (2 Replies)
Discussion started by: uxlunatick
2 Replies

5. SCO

I need SCO Openserver 4.2!!!!

I need SCO Openserver 4.2. Please, give me distributive of that version SCO:eek: (0 Replies)
Discussion started by: caine
0 Replies

6. UNIX for Advanced & Expert Users

SCO openserver 6 parallel port issues

I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies

7. UNIX for Dummies Questions & Answers

SCO Openserver 6.0

Hi guys, I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies

8. Filesystems, Disks and Memory

Parallel Port info?

is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices? Thanx /Nick (2 Replies)
Discussion started by: sajjan2
2 Replies

9. UNIX for Dummies Questions & Answers

sco openserver 5.5

hello! when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ? kindly help me thanks (1 Reply)
Discussion started by: buntty
1 Replies

10. UNIX for Dummies Questions & Answers

Help For SCO OpenServer

I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
Login or Register to Ask a Question
LPT(4)							   BSD Kernel Interfaces Manual 						    LPT(4)

NAME
lpt -- generic printer device driver SYNOPSIS
device ppc device ppbus device lpt DESCRIPTION
The current lpt driver is the port of the original lpt driver to the ppbus(4) system. One purpose of this port was to allow parallel port sharing with other parallel devices. Secondly, inb()/outb() calls have been replaced by ppbus function calls. lpt is now arch-independent thanks to the ppbus interface. See ppbus(4) for more info about the ppbus system. The parallel port bus is allocated by lpt when the printer device is opened and released only when the transfer is completed: either when the device is closed or when the entire buffer is sent in interrupt driven mode. The driver can be configured to be either interrupt-driven, or to poll the printer. Ports that are configured to be interrupt-driven can be switched to polled mode by using the lptcontrol(8) command. Depending on your hardware, extended capabilities may be configured with the lptcontrol(8) command. With an ECP/ISA port, you can take advantage of FIFO and DMA. In order to retrieve printer info from /dev/lpt0, just apply the cat command to the device. If the printer supports IEEE1284 nibble mode and has data to send to the host, you will get it. FILES
/dev/lpt0 first parallel port driver SEE ALSO
ppbus(4), ppc(4), lptcontrol(8) HISTORY
This driver replaces the functionality of the lpa driver, which is now defunct. BUGS
There are lots of them, especially in cheap parallel port implementations. It is only possible to open a lpt port when a printer is connected and on-line, making it impossible to run lptcontrol(8) when there is no printer connected. This driver could still stand a rewrite. BSD
February 14, 1999 BSD