Storage from SAN


 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Storage from SAN
# 8  
Old 11-17-2010
Yes but those are general guidelines, your vendor may have some specific recommendations.
# 9  
Old 11-17-2010
normally log comes while path is removed or added..
during the boot system can assign different device id and thus these logs are difference..

you must use at every modification..
Code:
/etc/init.d/multipathd reload

you can check the path integrity
Code:
# multipathd -k
multipathd> show paths

 
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Connecting to SAN storage - whats need to be done ?

hi all, I am on solaris 10 1/13 and new to SAN storage. I am required to connect to the LUNs on the SAN storage and is asked to provide the WWN information to the storage administrator. Right now, it will be just 1 connection from a single hba port to the FCport on the storage directly,... (1 Reply)
Discussion started by: javanoob
1 Replies

2. AIX

New to San Storage

Can anyone recommend a good book on san storage basics and how it communicates with an AIX server? (1 Reply)
Discussion started by: NycUnxer
1 Replies

3. Solaris

SAN Storage for ASM

Hi, We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN. The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes). I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
Discussion started by: esmgr
4 Replies

4. Solaris

Cannot see the IBM SAN storage

HI all, I had recently change the Server storage from EMC to the IBM SAN. but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server. When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies

5. Red Hat

how do we check SAN storage?

Hello, I am using LINUX OS. I want to check what is the SAN storage size. How do i check this in server? Any help is really appreciated.. (3 Replies)
Discussion started by: govindts
3 Replies

6. Solaris

SAN Storage to solaris 10 server

Hi, I have configured our SAN Storage to be connected to our new SUN T5220. On the SAn it looks all fine on the server I do not see any connection: cfgadm -al Ap_Id Type Receptacle Occupant Condition c1 scsi-bus connected ... (4 Replies)
Discussion started by: manni2
4 Replies

7. AIX

SAN storage and speed

I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Discussion started by: daveisme
1 Replies

8. Filesystems, Disks and Memory

Switching SAN storage

Hi, I have an existing SUN server that has a SAN storage installed on it. It also has softwares like Appwrox(scheduler), Taradata (database client), Samba Share and a few more installed on it. Now suppose that I have a new unix server server and i switch the same SAN store from the old unix... (1 Reply)
Discussion started by: myloginid
1 Replies

9. Solaris

Using San storage - advice needed

Thinking of using our San for network backups.. Have a Netra 240 being installed and planning to get some space on our San. Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Discussion started by: frustrated1
1 Replies
Login or Register to Ask a Question