Login or Register to Ask a Question and Join Our Community


UNIX for Advanced & Expert Users

Hme0 interfaces...

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Top Forums UNIX for Advanced & Expert Users Hme0 interfaces...
# 1  
Old 01-13-2002
Hme0 interfaces...
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?

Thanx Smilie

-Michelle
# 2  
Old 01-14-2002
under /etc you should create file "hostname.hme0:1" besides your hostname.hme0 that you have. and insdie this file insert your machinename-01

then with "ifconfig" cmd ,assign the new IP Address to this pesudo interface. as you see these procedures are for having two different ranges of IP Address at the same time.

Rgrds,
Nikk
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

can't see other interfaces

Hi Guys, I have a Netra240 server with four interfaces. However, when I ran this command dladm show-dev it showed only one interface bge0. Can someone please explain to me how to fix this problem? Thanks guys. (1 Reply)
Discussion started by: cjashu
1 Replies

2. Solaris

Interfaces and Virtual-interfaces queries

Hi Al, In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified. 1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many... (1 Reply)
Discussion started by: satish51392111
1 Replies

3. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies

4. Solaris

SUNW, hme0: Link Down - Cable problem

Ultra E150 Solaris 2.5.1 Oracle server. was working fine, then started losing network connection. I can see in messages file that it was complaining about another device using its ip address. Though not any longer, though I wonder if that was a red herring. My IT guys have now re-reserved its ip... (29 Replies)
Discussion started by: AlSmith1964
29 Replies

5. Solaris

Network Interfaces

I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies

6. Solaris

sun 420r hme0 not responding

I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network. If I ping 127.0.0.1 it says alive. Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies

7. UNIX for Dummies Questions & Answers

Changing Network Interface hme1 to hme0

I have sun solaris 9 installed but I have the interface configured to hme1 instead of hme0, our default value. Is there a way where i can rename the existing/working hme1 to hme0...? I want to showup the hmeo up if i say ifconfig -a.. rite now i see the hme1 up.. please advice if possible... (4 Replies)
Discussion started by: tintedwindow
4 Replies

8. Solaris

hme0 problem after reboot

Hi ..... My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command after reboot : # ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask... (1 Reply)
Discussion started by: tt155
1 Replies

9. UNIX for Dummies Questions & Answers

interfaces

Hello, which network interface i must sellect during the solaris9 installation le0 or hme0 ? this system is part of the network, it is a standalone system and is not on any domain. thanks for your help, em (1 Reply)
Discussion started by: emsakopa
1 Replies

10. UNIX for Advanced & Expert Users

hme0 babble -- ?

Dear Reader, I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages. The message is hme0: babble.. The port is up and alive. What does this message mean.. Is the on board port is about to fail?? Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
Login or Register to Ask a Question