Access to network interface (Mac-network)

Special Forums UNIX and Linux Applications Access to network interface (Mac-network)

03-08-2012

Registered User

1, 0

Join Date: Mar 2012

Last Activity: 8 March 2012, 9:42 AM EST

Posts: 1

Thanks Given: 0

Thanked 0 Times in 0 Posts

Access to network interface (Mac-network)

Hi,

I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.

berny88

View Public Profile for berny88

Find all posts by berny88

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

7. UNIX for Advanced & Expert Users

Network interface goes down intermittently

Hi all, I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem. Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and...

8. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error...

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT DEBIAN

guessnet-scan

GUESSNET-SCAN(8)					      System Manager's Manual						  GUESSNET-SCAN(8)

NAME

       guessnet-scan - guess network configuration data by looking at network traffic

SYNOPSIS

       guessnet-scan [options] [ethernet_interface]

DESCRIPTION

       Guessnet-scan tries to deduce network configuration data by watching network traffic at a given Ethernet interface.

       After  scanning	network  traffic  for some time, guessnet-scan prints a configuration string suitable for inclusion in /etc/network/inter-
       faces.

       Note that guessnet-scan uses heuristics and wild guesses and that the resulting data is not guaranteed to  be  accurate.   The  program	is
       intended to be used as a first try at getting network configuration data without bothering anyone.

OPTIONS

       Options follow the usual GNU conventions,

       --debug
	      Print debugging messages.

       --help Show a brief summary of commandline options.

       --init-time=int
	      Time in seconds to wait for the interface to initialize when it is not found already up at program startup.  Default: 3 seconds.

       -t, --timeout=int
	      Time in seconds to watch for network traffic.  Default: 5 seconds.

       -v, --verbose
	      Operate verbosely.

       --version
	      Show the version number of the program.

SCANNING REQUIREMENTS

       To  correctly  identify all data of the local network, guessnet-scan needs to see traffic related to a host in the local network and to the
       local gateway, if any.

       To be able to identify the network gateway, guessnet-scan also needs to see some traffic directed to the external network: you can help the
       detection  by  generating  some	outbound IP traffic during the scan, for example by browsing a web page (without proxy) or using telnet to
       open a connection to some remote host.

       Note that if you are connected to a switch, guessnet-scan won't probably be able to work, since the switch will isolate it from the network
       traffic that the other machines are generating.

SEE ALSO

       guessnet(8), interfaces(5).

AUTHOR

       Guessnet-scan was written by Enrico Zini <enrico@debian.org>.

								  10 October 2004						  GUESSNET-SCAN(8)

UNIX and Linux Applications