Access to network interface (Mac-network)

Special Forums UNIX and Linux Applications Access to network interface (Mac-network)

03-08-2012

Registered User

1, 0

Join Date: Mar 2012

Last Activity: 8 March 2012, 9:42 AM EST

Posts: 1

Thanks Given: 0

Thanked 0 Times in 0 Posts

Access to network interface (Mac-network)

Hi,

I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.

berny88

View Public Profile for berny88

Find all posts by berny88

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

7. UNIX for Advanced & Expert Users

Network interface goes down intermittently

Hi all, I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem. Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and...

8. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error...

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT OSF1

vb

vb(7)							 Miscellaneous Information Manual						     vb(7)

NAME

       vb, sys_attrs_vme_vba - VMEbus backplane Ethernet interface

SYNOPSIS

       controller vb0 at vba0

DESCRIPTION

       The  VMEbus  backplane (vb) interface provides access to an Ethernet network through the VMEbus backplane driver, which acts as an Ethernet
       Datalink Layer driver.  This interface allows VMEbus-based systems to communicate directly over the VMEbus to other VMEbus-based systems on
       the same backplane, or on other Ethernet connected systems outside the backplane through a gateway node on the backplane.

       Both  the  Tru64  UNIX  and VxWorks for Alpha (Version 3.1 or higher) software support the vb driver as well as communication between these
       systems on the same backplane.  The Tru64 UNIX vb driver is supported on AXPvme and Alpha VME SBCs and Alpha VME 2100 systems.

       The VMEbus backplane interface requires you to modify the /etc/sysconfigtab file on your AXPvme or Alpha VME system in order  to  configure
       the  vb driver and to map VMEbus windows for the system.  Mapping the VMEbus windows on one node requires knowledge about every node in the
       vb network.

									  Note

       Do not modify any vme_vba kernel subsystem attributes.  To configure a vb network node, you modify attributes of the vb	driver	(vb:)  and
       the system's VMEbus adapter (vba_vipvic: or vba_univ:).

       See System Configuration Supplement: OEM Platforms for detailed information about the use of the vb interface on Alpha VME systems, includ-
       ing the following topics: VMEbus backplane (vb) network overview Configuring vb network nodes  Modifying  vb  driver  attributes  Modifying
       vba_vipvic adapter attributes Modifying vba_univ adapter attributes Examples Related ioctl commands Diagnostic messages Errors

RELATED INFORMATION

       Interfaces:  sys_attrs_vba_vipvic(7), sys_attrs_vba_univ(7), sysconfigdb(8)

       Network Administration, System Configuration Supplement: OEM Platforms delim off

																	     vb(7)

UNIX and Linux Applications