Access to network interface (Mac-network)

Special Forums UNIX and Linux Applications Access to network interface (Mac-network)

03-08-2012

Registered User

1, 0

Join Date: Mar 2012

Last Activity: 8 March 2012, 9:42 AM EST

Posts: 1

Thanks Given: 0

Thanked 0 Times in 0 Posts

Access to network interface (Mac-network)

Hi,

I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.

berny88

View Public Profile for berny88

Find all posts by berny88

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

7. UNIX for Advanced & Expert Users

Network interface goes down intermittently

Hi all, I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem. Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and...

8. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error...

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT HPUX

vlan

VLAN(7) 						 Miscellaneous Information Manual						   VLAN(7)

NAME

       VLAN - virtual local area network

DESCRIPTION

       This manpage provides a brief overview of VLAN (virtual LAN) technology.

       VLANs  are logical, or network segments that can span multiple physical network segments.  A primary benefit of VLANs is that they can iso-
       late broadcast and multicast traffic by determining which destinations should receive that traffic, thereby making better use of switch and
       end-station resources.

       Logical	separation  using  VLAN allows for the logical grouping of PCs, servers and other network resources to behave as if they were con-
       nected to the same, physical segment, even if they are not.

       HP-UX VLAN is an implementation of IEEE 802.1p/Q standards.

       VLAN interfaces can be configured in HP-UX servers using the command (see nwmgr_vlan(1M)) or (see lanadmin_vlan(1M)).  HP  recommends  that
       you  use  for  HP-UX Release 11i Version 3 and forward.	Interfaces can also be configured using the web-based management tool HP-UX System
       Management Homepage (HP SMH).

       Each VLAN interface created is assigned a VLAN PPA (VPPA) that is unique across the system and a VLAN ID, that identifies the  virtual  LAN
       it is part of.  The VLAN ID is unique on the interface on which the VLAN interface is created.

WARNINGS

       The  and  commands are deprecated.  These commands will be removed in a future HP-UX release.  HP recommends the use of replacement command
       nwmgr(1M) to perform all network interface-related tasks.

SEE ALSO

       lanadmin(1M), lanadmin_vlan(1M), lanscan(1M), nwmgr(1M), nwmgr_vlan(1M), smh(1M).

       IEEE 802.1p, IEEE 802.1Q

																	   VLAN(7)

UNIX and Linux Applications