10 More Discussions You Might Find Interesting
1. AIX
Hi,
when I boot I get an E1DC error code. I've looked it up and it says that this error occurs during the firmware check. But the error is called "Dynamic Console Selection" .
1- Machine stopped at LCD led display = E1DC = CA00E1DC
E1DC Dynamic console selection. (maybe cable or keyboard)... (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
Hi guys,
My company just bought pseries server from ibm,
would like to ask , if first i need to install HMC for creating lpars ?
or first i need to install aix , and then install hmc?
Thx, (3 Replies)
Discussion started by: prpkrk
3 Replies
3. AIX
Hello,
I'm very rookie to AIX and attempting to install AIX. I have vio ready on the machine and don't know how to install OS? Inserted Volume 1 DVD into the ROM, don't know what to do next. Searched many forum but cant find the this basic thing. Please let me know how to install AIX on this... (4 Replies)
Discussion started by: pjeedu2247
4 Replies
4. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. Linux
Anyone can help me answer the question.
Why does they use Linux on IBM pSeries not AIX.
I can't understand why, cause AIX is the best supporting from IBM pSeries.
Tks you. (3 Replies)
Discussion started by: quan0509
3 Replies
7. AIX
Hello Gurus,
i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX.
Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk?
i tried:
# extendvg rootvg hdisk0... (2 Replies)
Discussion started by: sapbcer
2 Replies
8. AIX
Hi All --
I have an old 7028-6C1 which I'm using to learn AIX. The system didn't include a graphics card, so I connected via the serial port and performed a fresh install of AIX 5L V5.3.
Later, I purchased a GXT135P (2849) graphics card, and added it to the system. When I ran diag, I was able... (2 Replies)
Discussion started by: i386tech
2 Replies
9. UNIX for Dummies Questions & Answers
I'm new with UNIX, i have a pseries server from IBM and i need to install AIX 4.3, i never used wyse terminal or AIX, i need help to know how to install it, i have the server and the wyse i get in into the aixterm, over com1 but i don't know wich command use or what to do to install it..... ... (0 Replies)
Discussion started by: Juan-ito
0 Replies
10. AIX
I have been given some pSeries AIX servers to maintain. One of the servers wont come up after a shutdown and the following code is showing on the server:
10118401
How do I look up the error code? (2 Replies)
Discussion started by: dangral
2 Replies
vxdiskadd(1M) vxdiskadd(1M)
NAME
vxdiskadd - add one or more disks for use with Veritas Volume Manager
SYNOPSIS
vxdiskadd disk_address_pattern_list
DESCRIPTION
The vxdiskadd utility configures disks for use by Veritas Volume Manager (VxVM). Disks must already have been formatted. vxdiskadd
prompts the user for a disk group name and disk name for the disks. If no disk group name specified, the disks will be left as unassigned
replacement disks for future use. A new disk group may be created that will become the disks' disk group. If a disk group is specified for
the disks, the user is prompted for whether the disks should be designated as spares for the disk group. For new disks, all space on the
disk becomes free space in the disk's disk group. vxdiskadd interactively allows initialization to be done for all the disks specified or
allows the user to ask to make the decision for each disk individually.
One or more disks may be specified with a disk_address_pattern_list. The basic form of a disk address is c#t#d#. Any leading portion of
this address may be specified to indicate that all disks that match that leading portion should be used. For example c2t0 may be used to
specify all disks on controller 2, target 0. More than one disk address or address pattern may be specified on the command line. In case
of enclosure-based names, the disk address will be of the form enclosurename_diskno. The enclosurename indicates that all disks in the
specified enclosure are used. For example, emc1_ is used to specify all disks in the enclosure emc1. The word all may be used to specify
all disks on the system. Disk address names relate directly to device node names in the /dev/dmp and /dev/rdmp directories. Here are more
examples:
all: all disks
c3 c4t2: all disks on controller 3 and controller 4, target 2
c3t4d2: a single disk (in the c#t#d# naming scheme)
xyz_0 : a single disk (in the enclosure based naming scheme)
xyz_ : all disks on the enclosure whose name is xyz
The files /etc/vx/cntrls.exclude, /etc/vx/disks.exclude and /etc/vx/enclr.exclude may be used to exclude controllers or disks from use by
vxdiskadd. Each line of cntrls.exclude specifies the address of a controller to exclude, for example, c2. Each line of disks.exclude spec-
ifies a disk to exclude, for example, c0t3d0. Each line of enclr.exclude specifies the name of an enclosure to exclude, for example, enc0.
All courses of action that do not involve clear failure conditions require prompts from the user, with defaults supplied as appropriate.
Help is made available at every prompt. Entering ? in response to a prompt displays a context-sensitive help message.
OPERATIONS
Reconnecting a drive that was temporarily inaccessible
This situation is detected automatically by noting that the specified drive has a disk ID that matches a disk media record with no
currently associated physical disk. After reconnection, any stale plexes referring the disk are reattached, and any stopped volumes
referring the disk are restarted. This reattach action is performed by calling the vxrecover utility.
Initialization of a disk with reserved regions
Initialization of the disk is performed by calling vxdisksetup.
Adding a disk to an existing disk group
This operation can be performed independently of the initialization of the disk drive. The operation adds the disk to the group so
that its storage is added to the free space pool in that disk group. The vxassist utility can subsequently allocate from that free
space.
Creation of new disk groups in which to import a new disk
If disks are added that are required to be put into a disk group that does not exist, the option of creating the disk group is
offered.
Hardware-Specific Note
Some environments provide guidelines to optimize VxVM's interaction with intelligent storage systems. If these guidelines are present, VxVM
follows the guidelines when adding disks to disk groups. If the operation fails due to these guideline(s), you are prompted to use the
force option. The force option ignores any such storage-specific guidelines.
FILES
/etc/vx/cntrls.exclude Specifies the address of controllers to exclude from vxdiskadd operations.
/etc/vx/disks.exclude Specifies the address of disks to exclude from vxdiskadd operations.
/etc/vx/enclr.exclude Specifies the address of enclosures to exclude from vxdiskadd operations.
NOTES
EFI disks cannot be added to a disk group that is compatible with the Cross-platform Data Sharing (CDS) feature, nor can they be formatted
as CDS disks.
SEE ALSO
vxassist(1M), vxdisk(1M), vxdiskadm(1M), vxdisksetup(1M), vxintro(1M), vxrecover(1M)
VxVM 5.0.31.1 24 Mar 2008 vxdiskadd(1M)
