Hi all......I'm sorry if my english is not that good. Can somebody help me to about this error. I found it in message.log

Jan 16 18:22:42 ASM imapd[20204]: [ID 399336 local6.error] get_balanced_partition:[/export/home/data/link/mms11] -- chosen
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 899686 kern.info] NOTICE: [AFT0] Corrected system bus (CE) Event detected by CPU1 at TL=0, errID 0x00079931.a8388068
Jan 16 18:22:50 ASM AFSR 0x00000002<CE>.00000148 AFAR 0x00000000.42235fa0
Jan 16 18:22:50 ASM Fault_PC 0xfebd7f1c Esynd 0x0148 J0202
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 383328 kern.info] [AFT0] errID 0x00079931.a8388068 Corrected Memory Error on J0202 is Intermittent
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 856714 kern.info] [AFT0] errID 0x00079931.a8388068 Data Bit 90 was in error and corrected
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 717792 kern.info] [AFT2] errID 0x00079931.a8388068 PA=0x00000000.42235f80
Jan 16 18:22:50 ASM E$tag 0x00000001.08920000 E$state_6 Modified
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 895151 kern.info] [AFT2] E$Data (0x00) 0x00000000.00000001 0x00000000.00000000 ECC 0x064
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 895151 kern.info] [AFT2] E$Data (0x10) 0xfee14674.00000000 0x000a0c8c.00000000 ECC 0x1e2
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 895151 kern.info] [AFT2] E$Data (0x20) 0x00000000.00000000 0x00000000.0008eda8 ECC 0x194
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 895151 kern.info] [AFT2] E$Data (0x30) 0x001db20c.fee14674 0xfe205fe8.00000000 ECC 0x1e6
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 929717 kern.info] [AFT2] D$ data not available
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 335345 kern.info] [AFT2] I$ data not available
Jan 16 18:22:50 ASM SUNW,UltraSPARC-III+: [ID 202015 kern.info] NOTICE: [AFT0] Corrected system bus (CE) Event detected by CPU0 at TL=0, errID 0x00079931.a854f018
Jan 16 18:22:50 ASM AFSR 0x00000002<CE>.00000148 AFAR 0x00000000.42235e60
Jan 16 18:22:50 ASM Fault_PC 0xfee708f8 Esynd 0x0148 J0202

Just for your info, I'm use sun fire 280R and i was change the memory 1 month ago. Is the problem still about the memory ? Is there anything I can do beside changing the memory again ?
Thanx

Hi,

First of let me know, did you replaced the same memory module (same slot) one month before...??? After replacing the memory this time, run the post at OK prompt in a maximum mode by putting the setting "diag-level=max"

Hardware failures are common, but you can check out about heat near by your server if memory is failing every month.

Regards,
jumadhiya.

Thank you for your reply.....

Yes we has change the memory at the same slot. Is there any other way to change the setting without running the post ? Is there any big impact to other program if i didn't fix it soon ?