Hardware raid patching


 
Thread Tools Search this Thread
Operating Systems Solaris Hardware raid patching
# 8  
Old 01-12-2015
Well you would be well advised to take a backup (especially of the root filesystem) before patching in case it goes wrong.

How do you backup this system now?

I would recommend taking a ufsdump (using fssnap and ufsdump commands) to either a tape drive or over the network via NFS to another system. I would also ensure that you have a copy of the vtoc (virtual table of contents) (using the prtvtoc command). Having that is priceless in the event that recovery is necessary. Once you've done that you have a full copy of your data even if, at this time, you don't know how to restore it.

Once that's done you can apply your required patches and/or Oracle recommended patchset.
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID using three disks

Dear All , Pl find the below command , # raidctl -l Controller: 1 Volume:c1t0d0 Disk: 0.0.0 Disk: 0.1.0 Disk: 0.3.0 # raidctl -l c1t0d0 Volume Size Stripe Status Cache RAID Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies

2. Solaris

Patching on Raid 0 Disk

Dear All , We need to do patching on one Solaris Server , where we have raid 0 configured. What is the process to patch a Server if RAID 0 (Concat/Stripe) is there. Below is the sample output. # metadb flags first blk block count a m pc luo 16 ... (1 Reply)
Discussion started by: jegaraman
1 Replies

3. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My... (4 Replies)
Discussion started by: KhawHL
4 Replies

4. Hardware

Sun T3-1 hardware RAID

Hi all I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS. The documentation doesn't make it clear if: 1. The... (6 Replies)
Discussion started by: soliberus
6 Replies

5. Solaris

Hardware Raid - LiveUpgrade

Hi, I have a question. Do LiveUpgrade supports hardware raid? How to choose the configuration of the system disk for Solaris 10 SPARC? 1st Hardware RAID-1 and UFS 2nd Hardware RAID-1 and ZFS 3rd SVM - UFS and RAID1 4th Software RAID-1 and ZFS I care about this in the future to take... (1 Reply)
Discussion started by: bieszczaders
1 Replies

6. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help. (2 Replies)
Discussion started by: presul
2 Replies

7. Solaris

T2000 Hardware RAID

Hi, I have a root with hardware RAID on c0t0d0 and c0t2d0. I would like to set the boot device sequence in OBP for both hdds. I have checked in ls -l /dev/rdsk/ for the path of c0t2d0 but it does not exist. Can anyone shed some lights on this? AVAILABLE DISK SELECTIONS: 0.... (12 Replies)
Discussion started by: honmin
12 Replies

8. Solaris

how to hardware RAID 1 on T5120

Hi, I have t5120 sparc and I have 2 146 G drives in the system. I will be installing solaris 10 and also want the system mirrored using Hardware RAID "1" The System did come preinstalled as it comes from sun. I did not do much on it. I booted system using boot cdrom -s gave format... (6 Replies)
Discussion started by: upengan78
6 Replies

9. Solaris

Hardware RAID

I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies
Login or Register to Ask a Question
EDIT-PATCH(1)						      General Commands Manual						     EDIT-PATCH(1)

NAME
edit-patch, add-patch - tool for preparing patches for Debian source packages SYNOPSIS
edit-patch path/to/patch add-patch path/to/patch DESCRIPTION
edit-patch is a wrapper script around the Quilt, CDBS, and dpatch patch systems. It simplifies the process of preparing and editing patches to Debian source packages and allows the user to not have to be concerned with which patch system is in use. Run from inside the root directory of the source package, edit-patch can be used to edit existing patches located in debian/patches. It can also be used to incorporate new patches. If pointed at a patch not already present, it will copy the patch to debian/patches in the correct format for the patch system in use. Next, the patch is applied and a subshell is opened in order to edit the patch. Typing exit or pressing Ctrl-d will close the subshell and launch an editor to record the debian/changelog entry. edit-patch is integrated with the Bazaar and Git version control systems. The patch will be automatically added to the tree, and the debian/changelog entry will be used as the commit message. If no patch system is present, the patch is applied inline, and a copy is stored in debian/patches-applied. add-patch is the non-interactive version of edit-patch. The patch will be incorporated but no editor or subshell will be spawned. AUTHORS
edit-patch was written by Daniel Holbach <daniel.holbach@canonical.com>, Michael Vogt <michael.vogt@canonical.com>, and David Futcher <bobbo@ubuntu.com>. This manual page was written by Andrew Starr-Bochicchio <a.starr.b@gmail.com>. Both are released under the terms of the GNU General Public License, version 3. DEBIAN
Debian Utilities EDIT-PATCH(1)