10 More Discussions You Might Find Interesting
1. Solaris
In Solaris 10 it was easy, a simple grep through modinfo output and you'd have the version of any loaded module, including your NIC drivers. In my career I've seen many people relying on this information in their scripts. Now I'm on Solaris 11, and where have the version numbers gone? The... (0 Replies)
Discussion started by: cambridge
0 Replies
2. Linux
Hi All,
I am trying to make rpm package for unixODBC driver manager 2.3.0 using below spec file. During rpmbuild i am getting the error. Can you pls advice how we can overcome this issue
%define name unixODBC
%define ver 2.3.0
%define prefix /usr
%define sysconfdir /etc
%define libdir... (2 Replies)
Discussion started by: kamauv234
2 Replies
3. Programming
Hi, all:
My writed NIC driver for rtl8139d adapter on linux 3.0.4 cannot send and recieve simultaneously but is able to send or recieve in parallel respectively. As soon as it send and recieve at the same time, the transmmition rate on both directions gradually decrease to zero b/s and report... (1 Reply)
Discussion started by: liklstar
1 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. UNIX for Advanced & Expert Users
Hi, all:
How can I know whether the packets recieved from network by my own NIC driver are transmitted to upper layer(IP layer) or not?
How can I know if the packets come from upper layer are passed to my own NIC driver and go out further?
Is there any shell command or utility show... (9 Replies)
Discussion started by: liklstar
9 Replies
6. Red Hat
Guys,
Can you help me how to verify the current installed NIC driver version in RHEL5.3?
Thanks.:D (1 Reply)
Discussion started by: shtobias
1 Replies
7. SCO
hi
I have a fresh installation of SCO 5.0.6 and I have download a NIC driver for Intel Pro 1000:
ftp://ftp.sco.com/pub/openserver5/507/drivers/eeG_5.0.7g/VOL.000.000
Howto install it using floppy?
---------- Post updated at 04:02 PM ---------- Previous update was at 02:18 PM... (0 Replies)
Discussion started by: ccc
0 Replies
8. IP Networking
Hi
I need to know how a driver for a network interface card works, I want to learn the basic principles since I know that every driver has its specific implementation.
For example when we speak about the scheduler, we can read an operating system book and learn general design concepts e.g.... (0 Replies)
Discussion started by: Puntino
0 Replies
9. UNIX for Advanced & Expert Users
Hi:-
I am trying to install a device driver for Intel NIC card on TurboLinux, but getting following errors,
cc -O -Wall -o eepro100-diag eepro100-diag.c
eepro100-diag.c:72: unistd.h: No such file or directory
eepro100-diag.c:73: stdio.h: No such file or directory
eepro100-diag.c:74:... (1 Reply)
Discussion started by: s_aamir
1 Replies
10. UNIX for Dummies Questions & Answers
I'm way confused. I loaded RH 7.1 on an old P-75 Compaq. IT has an EtherExpress pro/100 card in it and I have that attached to the optional port on our firewall with a crossover....I can't seem to get the card to negotiate with the firewall...it's currently 100Meg at Half duplex. I'm at a loss... (3 Replies)
Discussion started by: kwalter
3 Replies
MY(4) BSD Kernel Interfaces Manual MY(4)
NAME
my -- Myson Technology Ethernet PCI driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device my
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_my_load="YES"
DESCRIPTION
The my driver provides support for various NICs based on the Myson chipset. The Myson chipset is a variant of the DEC Tulip NIC chipset.
The driver will work with almost any MII-compliant PHY, thus failure to positively identify the chip is not a fatal error.
HARDWARE
The my driver provides support for various NICs based on the Myson chipset. Supported models include:
o Myson MTD800 PCI Fast Ethernet chip
o Myson MTD803 PCI Fast Ethernet chip
o Myson MTD89X PCI Gigabit Ethernet chip
SEE ALSO
altq(4), de(4), netintro(4), pci(4), ifconfig(8)
HISTORY
The my driver first appeared in FreeBSD 4.6.
AUTHORS
The my driver was written by Myson Technology Inc.
This manual page was written by Hiten M. Pandya <hmp@FreeBSD.org>.
BUGS
The my driver does not support Power Management Events (PME).
BSD
March 11, 2007 BSD
