9 More Discussions You Might Find Interesting
1. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
2. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
3. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
4. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
5. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
6. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
7. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
8. Solaris
Hi there,
I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server.
*I have re-compiled the linux kernel t support ufs fstype with ro mount support.
filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies
9. BSD
Hello All,
How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies
ISCSI_INITIATOR(4) BSD Kernel Interfaces Manual ISCSI_INITIATOR(4)
NAME
iscsi_initiator -- kernel driver for the iSCSI protocol
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device iscsi_initiator
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
iscsi_initiator_load="YES"
DESCRIPTION
The iscsi_initiator implements the kernel side of the Internet SCSI (iSCSI) network protocol standard. The userland companion is
iscontrol(8), and permits access to remote virtual SCSI devices via cam(4).
SYSCTL VARIABLES
debug.iscsi_initiator set the debug-level, 0 means no debugging, 9 for maximum.
net.iscsi.isid the initiator part of the Session Identifier.
The following are informative only:
net.iscsi.driver_version the current version of the driver.
net.iscsi.sessions the number of current active sessions.
net.iscsi.n.targetname the target name of session n.
net.iscsi.n.targedaddress the IP address of the target of session n.
net.iscsi.n.stats statistics for session
net.iscsi.n.pid the process id of the userland side of session n, see iscontrol(8).
FILES
The iscsi_initiator driver creates the following:
/dev/iscsi used to create new sessions.
/dev/iscsi%d for each new session.
SEE ALSO
cam(4), camcontrol(8), iscontrol(8)
STANDARDS
iSCSI RFC 3720
BUGS
The lun discovery method is old-fashioned.
BSD
May 9, 2010 BSD