8 More Discussions You Might Find Interesting
1. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
2. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
3. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
4. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
5. Solaris
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies
6. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
7. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
8. Solaris
Hello!
I have several disks discovered using iscsi protocol.
There disks are represented in OS like c2txd0 .
logs:
Is it possible to change drive path, for example, from c2t6d0 to c2t7d0?
It's important for me because I have to install oracle RAC on RAW devices.
NIck (0 Replies)
Discussion started by: skelet
0 Replies
list_devices(1) list_devices(1)
NAME
list_devices - list allocatable devices
SYNOPSIS
list_devices [-s] [ -U uid] -l [device]
list_devices [-s] [ -U uid] -n [device]
list_devices [-s] [ -U uid] -u [device]
The list_devices utility lists the allocatable devices in the system according to specified qualifications.
The device and all device special files associated with the device are listed. The device argument is optional and, if it is not present,
all relevant devices are listed.
The following options are supported:
-l [device] Lists the pathname(s) of the device special files associated with the device that are allocatable to the current process.
If device is given, lists only the files associated with the specified device.
-n [device] Lists the pathname(s) of device special files associated with the device that are allocatable to the current process but
are not currently allocated. If device is given, lists only the files associated with that device.
-s Silent. Suppresses any diagnostic output.
-u [device] Lists the pathname(s) of device special files, associated with the device that are allocated to the owner of the current
process. If device is given, list only the files associated with that device.
-U uid Uses the user ID uid instead of the real user ID of the current process when performing the list_devices operation. Only a
user with the solaris.device.revoke authorization can use this option.
The following exit values are returned:
non--zero An error occurred.
/etc/security/device_allocate
/etc/security/device_maps
/etc/security/dev/*
/usr/security/lib/*
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
allocate(1), deallocate(1), bsmconv(1M), dminfo(1M), mkdevalloc(1M), mkdevmaps(1M), device_allocate(4), device_maps(4), attributes(5)
The functionality described in this man page is available only if the Basic Security Module (BSM) has been enabled. See bsmconv(1M) for
more information.
/etc/security/dev, mkdevalloc(1M), and mkdevmaps(1M) might not be supported in a future release of the Solaris Operating Environment.
28 Mar 2005 list_devices(1)