network card physical reset error


 
Thread Tools Search this Thread
Special Forums Cybersecurity network card physical reset error
# 1  
Old 02-15-2002
network card physical reset error

Hi all

I am facing some problem with network card
i am using solaris8 and on sunultra10 .As it is my firewal machine i have got on backup harddisk for any emergency.

In one hardidsk while installation only hme0 interface was configured and in the backup hard disk qfe0/hme0 both are configured and now due to some problem i am puting the backup hard disk and trying to boot One error is coming like

there is no interface hme0
SW Hme0 phy reset error this message is coming continuously.
for qfe0 interface also the same mesage is coming.
But when i am putting the oringinal harddisk both the interfaces are succesfully configured.


please suggest.as i wan't the back disk to be used for some time.

waiting for ur suggestion.
thanks
PRAFUL
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies

2. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

3. Solaris

dependency require_all/none svc:/network/physical (maintenance)

I am using telnet instead of ssh because network/physical service is on maintenance mode. I can ping google and other internel machines. I can't ssh to this server because network/physical is dependency of ssh. How can I fix this service. I can use network service but it is maintenance mode.... (8 Replies)
Discussion started by: getrue
8 Replies

4. Solaris

svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96. [ n

After a memory upgrade all network interfaces are misconfigued. How do i resolve this issue. Below are some out puts.thanks. ifconfig: plumb: SIOCLIFADDIF: eg000g0:2: no such interface # ifconfig eg1000g0:2 plumb ifconfig: plumb: SIOCLIFADDIF: eg1000g0:2: no such interface # ifconfig... (2 Replies)
Discussion started by: andersonedouard
2 Replies

5. Solaris

Network interface statistic reset

Hi, all! Can anybody tell me how can I reset network statistic, which could be seen by command 'netstat -i' or 'dladm show-dev -s'? Thank you for advance Christian (2 Replies)
Discussion started by: Inventor
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

[need help] error after configure network card at v890 sparc

hi experts, i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display : WARNING: ce0: fault detected external to device; service degraded WARNING: ce0: xcvr addr:0x01 - link down configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies

8. Solaris

Testing physical network connection

How do you test the physical network connection of an interface in solaris. I know that if you have an active connection and the cable gets yanked, you can look in the messages file to check for link failure messages. But is there any better way to see if you have good layer 2 connectivity? (1 Reply)
Discussion started by: tjlst15
1 Replies

9. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
Login or Register to Ask a Question
OPENSC-TOOL(1)							   OpenSC Tools 						    OPENSC-TOOL(1)

NAME
opensc-tool - generic smart card utility SYNOPSIS
opensc-tool [OPTIONS] DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or sending arbitrary APDU commands to a card. OPTIONS
--atr, -a Print the Answer To Reset (ATR) of the card. Output is in hex byte format --card-driver driver, -c driver Use the given card driver. The default is auto-detected. --info, -i Print information about OpenSC, such as version and enabled components. --list-drivers, -D List all installed card drivers. --list-files, -f Recursively list all files stored on card. --list-readers, -l List all configured readers. --name, -n Print the name of the inserted card (driver). --reader num, -r num Use the given reader number. The default is 0, the first reader in the system. --send-apdu apdu, -s apdu Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF.... --serial Print the card serial number (normally the ICCSN). Output is in hex byte format --verbose, -v Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library. --wait, -w Wait for a card to be inserted. SEE ALSO
opensc-explorer(1) opensc 06/17/2014 OPENSC-TOOL(1)