I have 3 RHEL 5.7 servers. So I decided to upgrade them to latest version. 2 of them successfully upgraded to RHEL 5.11 and last one is the problem.
When I hit rhn_register command server shows following info :
Code:
#rhn_register
There was an SSL error: (104, 'Connection reset by peer')
A common cause of this error is the system time being incorrect. Verify that the time on this system is correct.
Below are steps I have tried.
1. So I checked data and timezone on the server. They all correct.
Checked /var/log/up2date log file. Following errors occured.
Code:
rhn_register A protocol error occured: Service Unavailable , attempt #1,
rhn_register A protocol error occured: Service Unavailable , attempt #2,
2. Checked the https and http connection to xmlrpc.rhn.redhat.com with telnet tool. Successfully connected via https and http.
3. Replaced http instead of https in /etc/sysconfig/rhn/up2date file and tried to register with rhn. But with no luck.
4. Checked root certificates. They all fine.
Now I'm running out of ideas. Is there anything to check?
Thanks guys
bond0 active in eth0 and inactive in eth4. why eth4 received network package?
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: eth0 (primary_reselect failure)
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
... (4 Replies)
Hi,
I am on Redhat 5. on the /etc/sysconfig/network file
I don't see GATEWAY as one line. I also checked /etc/sysconfig/network-scripts/ifcfg-eth0. I don't see GATEWAY.
But on the server. But when I do netstat -rn. I see many address. Is there some other settings ?
... (2 Replies)
Hi,
We are having many RedHat linux Server with Cluster facility for availability of service like HTTPD / MySQL.
We face some issue while some issue related to power disturbance / fluctuation or Network failure. There is two Cluster Node configured in... (0 Replies)
Hi.
I'm having problems on multiple Red Hat VM's (on esxi) whereby the network interface IRQ is disabled by the OS. This is the error from dmesg:
command: Write(10): 2a 00 03 42 3f e0 00 00 08 00
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81018b45c680)
irq 67: nobody cared (try... (0 Replies)
Hi
I have a problem related to vxvm. I am using redhat5.4 64 bit
vxassist -g mydg growto my-vol 2G (Actually when i am running this command then this command is not increasing the size of volume but this command is running fine and the size which i have given to my volume it has been reduced... (0 Replies)
Buenas,
Tengo 3 sistemas registrados en redhat network; hace un mes modificamos las ip's de los mismos pero en redhat network igue poniendo las antiguas. Como puedo modificarlas? tengo q registrar los sistemas de nuevo?
Otra cosilla, he intentado actualizar packages y erratas: en actualizar ahora... (4 Replies)
Discussion started by: fuentepinel
4 Replies
7. Forum Support Area for Unregistered Users & Account Problems
When I'm trying to register it says that my e-mail adress )is banned by administrator. Why?
Thanks
PS The same problem occurs with other 2 adresses I have (1 Reply)
I rlogin from a sco box to a redhat box and run /bin/vi. Pgup, Pgdn, and arrow up/down keys don't work. I enter "export TERM=ansi80x25" and run vi again.Everything works just like I like it. Except the cursor turns into a blinking overscore. When I exit vi and close the connection to redhat,... (2 Replies)
Hi All
My first post so I hope it's ok.
I have VMware workstation 5.0.0 build-13124 on an XP professional box. Within the VMware environment I have two virtual systems. The first is a Red Hat Linux (3.2.2-5) box and the second is an XP Home (sp2) box. When setting up both virtual boxes I set... (1 Reply)
11-02-2014
