Jeg prøver å installere en HP StorageWorks DAT40 båndstasjonen på SC0 5.0.7. På båndstasjonen ikke fungerer.

Når jeg kjører # sconf-v dette er det jeg får;

Sdsk ad160 0 0 0 0
Sdsk ad160 0 0 1 0
Stp ad160 0 0 3 0

Men når jeg kjører # hwconfig-h dette er det jeg får;

enhet adresse Flere DMA kommentar
\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d \u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d\u003d
kjerne - - - rel \u003d 3.2v5.0.7 gutt \u003d 2003-02-18
CPU - - - unit \u003d 1 familie \u003d 15 type \u003d Intel Xeon
cpuid - - - unit \u003d 1 vend \u003d GenuineIntel tfms \u003d 0:15:2:9 (11)
fpu - 13 - unit \u003d 1 type \u003d 80387-kompatibel
PCI 0xcf8-0xcff - - am \u003d 1 sc \u003d 0 busser \u003d 3
PNP - - - noder \u003d 0
klokke - - - type \u003d TSC/2.392032383Ghz
seriell 0x3f8-0x3ff 4 - unit \u003d 0 type \u003d Standard nports \u003d 1 base \u003d 0 16550A/16
konsollen - - - unit \u003d VGA-type \u003d 0, num \u003d 12 scoansi \u003d 1 rull \u003d 50
adapter 0xd800-0xd8ff 11 - type \u003d ad160 ha \u003d 0 slot \u003d 0 buss \u003d 0 id \u003d 7 FTS \u003d Sto
adapter 0xdc00-0xdcff 3 - type \u003d ad160 ha \u003d 1 slot \u003d 0 buss \u003d 0 id \u003d 7 FTS \u003d Sto
Floppy 0x3f2-0x3f7 6 2 enhet \u003d 0 type \u003d 135ds18
UDI - - - UDI miljø
adapter - - - ha \u003d 0 type \u003d usb_msto UDI SCSI HBA
adapter 0x170-0x177 15 - type \u003d IDE ctlr \u003d videregående DVR \u003d WD
bcme0 - 3 - chip \u003d BCM5703 mem \u003d FCD00000 grafi \u003d BCM5703 DDR \u003d 00:10: 18:06:49:56
CD-ROM - - - type \u003d IDE enhet \u003d 0 ctlr \u003d sec CFG \u003d mst DVR \u003d Srom-> WD
disk - - - type \u003d S ha \u003d 0 id \u003d 0 LUN \u003d 0 buss \u003d 0 HT \u003d ad160 enhet \u003d 0
Sdsk - - - cyls \u003d 4427 HDS \u003d 255 sek \u003d 63 unit \u003d 0 FTS \u003d stdb
Sdsk-0 - - - Vnd \u003d SEAGATE Prd \u003d ST336753LW Rev \u003d DX10
usb_ohci - 5 - PCI-bussen \u003d 0 dev \u003d 15 func \u003d 2

Jeg bruker Lone tar som backup-programvare, og den ikke gjenkjenner båndet når jeg utfører et søk.