upscode2(8) [php man page]

UPSCODE2(8)							    NUT Manual							       UPSCODE2(8)

NAME

       upscode2 - Driver for UPScode II compatible UPS equipment

NOTE

       This man page only documents the hardware-specific features of the upscode2 driver. For information about the core driver, see
       nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports UPS equipment which can be controlled via the UPScode II protocol. This is mainly Fiskars, Powerware equipment, but
       also some (probably OEM'ed) products from Compaq.

EXTRA ARGUMENTS

       This driver supports the following optional settings in the ups.conf(5):

       manufacturer=value
	   Autodetection of this parameter is not possible yet (and it probably never will be). Therefore, this user-defined string accepts any
	   name. The default is unknown.

       input_timeout=value
	   The timeout waiting for a response from the UPS. Some UPS models have shown to be rather slow, resulting in frequent messages about
	   empty responses from the UPS. If you see this, try increasing this value.

       output_pace=value
	   Delay between characters sent to the UPS. This was added for completeness with the above parameter. It has not shown to be needed yet.

       baudrate=value
	   The default baudrate is 1200, which is the standard for the UPScode II protocol.

       full_update_timer=value
	   Number of seconds between collection of normative values.

       use_crlf
	   Flag to set if commands towards to UPS need to be terminated with CR-LF, and not just CR.

       use_pre_lf
	   Flag to set if commands towards to UPS need to be introduced with an LF. A Compaq T1500h is known to need this.

COMMANDS

       The driver supports the following commands for those UPSen that support them. The available commands are autodetected during
       initialization, so you should check availability with upscmd -l.

       o   test.panel.start - Start UPS self test

       o   test.battery.start - Start battery self test

       o   beeper.enable - Enable UPS beeper

       o   beeper.disable - Disable UPS beeper

       o   shutdown.return - Shut down in 1 second and wait for power to return

       o   shutdown.stayoff - Shut down in 1 seconds

       o   shutdown.reboot - Shut down in 1 seconds and reboot after 1 minute

       o   shutdown.reboot.graceful - Shut down in 20 seconds and reboot after 1 minute

NOTES

       The Powerware UPS models that this driver has been tested against until now have not returned a value for battery.charge. Therefore, the
       driver will guestimate a value based on the nominal battery min/max and the current battery voltage.

AUTHOR

       Havard Lygre <hklygre@online.no>, Niels Baggesen <niels@baggesen.net>

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/

Network UPS Tools						    05/21/2012							       UPSCODE2(8)

Check Out this Related Man Page

SAFENET(8)							    NUT Manual								SAFENET(8)

NAME

       safenet - Driver for SafeNet compatible UPS equipment

NOTE

       This man page only documents the hardware-specific features of the safenet driver. For information about the core driver, see nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports UPS equipment which can be controlled via SafeNet v1.0 for Windows (serial interface only).

EXTRA ARGUMENTS

       This driver supports the following optional settings in the ups.conf(5) file:

       manufacturer=value
	   Autodetection of this parameter is not possible yet (and it probably never will be). Therefore, this user-defined string accepts any
	   name. The default is unknown.

       modelname=value
	   Like manufacturer above. The default is unknown.

       serialnumber=value
	   Like manufacturer above. The default is unknown.

       ondelay=value
	   Time to wait before switching on the UPS (minutes). Defaults to 1 minute.

       offdelay=value
	   Time to wait before shutting down the UPS (seconds). Defaults to 30 seconds.

UPSCMD

       This driver supports some instant commands (see upscmd(8)):

       test.battery.start
	   Start UPS self test

       test.battery.stop
	   Cancel UPS self test

       test.failure.start
	   Start simulated power failure

       test.failure.stop
	   Cancel simulated power failure

       beeper.enable
	   Enable the UPS beeper

       beeper.mute
	   Temporarily mute the UPS beeper

       beeper.toggle
	   Toggle the UPS beeper

       shutdown.return
	   Turn off the load and wait for the power to return. Uses the timer defined by offdelay.

       shutdown.reboot
	   Turn off the load and return. Uses the timers defined by offdelay and ondelay.

KNOWN PROBLEMS

       If you run the shutdown.return command with mains present, the output may stay on or switch off and not back on again. The shutdown.reboot
       command will unconditionally switch on the load again (with or without mains present).

       If the driver is called with the -k option (or through upsdrvctl shutdown) it tries to detect which command should be used in an attempt to
       stay off until mains is present again or to cycle the output if the power returned in the mean time. This isn't bullet-proof, and you
       should be prepared that the power will either not be shutdown, or that it doesn't return when the power comes back.

AUTHOR

       Arjen de Korte <adkorte-guest at alioth.debian.org>

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/

Network UPS Tools						    05/21/2012								SAFENET(8)

Linux and UNIX Man Pages

upscode2(8) [php man page]

Check Out this Related Man Page