SICONTROL(8) BSD System Manager's Manual SICONTROL(8)NAME
sicontrol -- Specialix SI/XIO driver configuration and debugging
SYNOPSIS
sicontrol device command [param ...]
DESCRIPTION
The sicontrol utility is used to configure and monitor the SI/XIO device driver.
The sicontrol utility operates on the specified device to indicate which port is to be used.
The special device string `-' is used to indicate the global driver settings instead.
A /dev/ is included if necessary.
The following commands are used for the global settings and should be specified with the '-' device name:
int_throttle [value]
Configure the `aggregate interrupt throttle value'. The maximum number of host adapter interrupts per second is determined by:
controller CPU clock / (8 * int_throttle)
The default value at boot time is 25000. The host adapter cpu clock is 25MHz. This gives a maximum interrupt rate of about 125 inter-
rupts per second.
Lowering this value will increase the rate in which the host adapter can interrupt the operating system for attention.
rxint_throttle [value]
Configure the receiver interrupt throttle value. The default value of 4 at boot time allows an interrupt rate of approximately 25.
Lowering this value will increase the rate in which the host adapter can interrupt the operating system to empty the receiver fifos.
nport
Return the number of ports under the control of the device driver.
The following commands are used for the individual ports and should be specified with a device name from /dev:
mstate
Show the current incoming modem control signals.
ccbstat
Show the current "ccb" structure for the specified port. This is not of much use outside of debugging the driver and determining why a
port is wedged.
FILES
/dev/si_control global driver control file for use by sicontrol
/dev/ttyA* terminal control ports
/dev/ttyiA* initial termios state devices, for use by stty(1)
/dev/ttylA* locked termios state devices, for use by stty(1)DIAGNOSTICS
Generally self explanatory.....
SEE ALSO stty(1), si(4), termios(4), tty(4), comcontrol(8)HISTORY
The sicontrol utility is loosely based on a utility called siconfig which was written by Andy Rutter <andy@acronym.co.uk>.
Specialix International do not support this device driver in any way.
AUTHORS
Peter Wemm <peter@FreeBSD.org>
BUGS
Bound to be many... :-)
BSD September 26, 1995 BSD
Check Out this Related Man Page
SI(4) BSD Kernel Interfaces Manual SI(4)NAME
si -- driver for Specialix International SI/XIO or SX intelligent serial card
SYNOPSIS
device si
For ISA host cards put the following lines in /boot/device.hints:
hint.si.0.at="isa"
hint.si.0.maddr="0xd0000"
hint.si.0.irq="12"
DESCRIPTION
The Specialix SI/XIO and SX hardware makes up an 8 to 32 port RS-232 serial multiplexor.
The system uses two components: a "Host adapter", which is plugged into an ISA, EISA or PCI slot and provides intelligence and buffering/pro-
cessing capabilities, as well as an external bus in the form of a 37 pin cable.
On this cable, "modules" are connected. The "SI" module comes in a 4 and 8 port version. The "XIO" and "SX" modules come only in 8 port
versions.
The host adapter polls and transfers data between the modules and the rest of the machine. The Host adapter provides a 256 byte transmit and
256 byte receive FIFO for each of the 32 ports that it can maintain.
The XIO modules can operate each of their 8 ports at 115,200 baud. The SI version can run at 57,600 baud. The SX modules can operate each
of their 8 ports at up to 921,600 baud.
SX modules are only supported when connected to an SX host card. SI or XIO modules are supported on any host card.
The host adapter uses a shared memory block in the traditional ISA bus "hole" between 0xA0000 and 0xEFFFF. The adapter can be configured
outside range, but requires the memory range to be explicitly non-cached. The driver does not yet support this mode of operation.
SX ISA Host cards have an 8/16 bit mode switch or jumper on them. This switch or jumper MUST be set for 8 bit mode.
The ISA adapters can use Irq's 11, 12 or 15 (and 9 and 10 in the case of SX host cards).
The si device driver may have some of its configuration settings changed at run-time with the sicontrol(8) utility.
The si device driver also responds to the comcontrol(8) utility for configuring drain-on-close timeouts.
The driver also defines 3 sysctl variables that can be manipulated: machdep.si_debug sets the debug level for the whole driver. It depends
on the driver being compiled with SI_DEBUG. machdep.si_pollrate sets how often per second the driver polls for lost interrupts.
machdep.si_realpoll sets whether or not the card will treat the poll intervals as if they were interrupts.
An open on a /dev device node controlled by the si driver obeys the same semantics as the sio(4) driver. It fully supports the usual seman-
tics of the cua ports, and the "initial termios" and "locked termios" settings. In summary, an open on a tty port will block until DCD is
raised, unless O_NONBLOCK is specified. CLOCAL is honored. An open on a cua port will always succeed, but DCD transitions will be honored
after DCD rises for the first time.
Up to four SI/XIO host cards may be controlled by the si driver. Due to the lack of available interrupts, only 3 ISA SI/XIO host cards can
be used at once.
The lowest 5 bits of the minor device number are used to select the port number on the module cluster. The next 2 bits select which of 4
host adapter cards. This allows a maximum of 128 ports on this driver.
Bit 7 is used to differentiate a tty/dialin port (bit 7=0) and a cua/callout port (bit 7=1).
Bit 8 through 15 (on FreeBSD) are unavailable as they are a shadow of the major device number.
If bit 16 is a 1, the device node is referring to the "initial state" device. This "initial state" is used to prime the termios(4) settings
of the device when it is initially opened. If bit 17 is a 1, the device node is referring to the "locked state" device. The "locked state"
is used to prevent the termios(4) settings from being changed.
To manipulate the initial/locked settings, the stty(1) command is useful. When setting the "locked" variables, enabling the mode on the lock
device will lock the termios mode, while disabling the mode will unlock it.
FILES
/dev/si_control global driver control file for sicontrol(8)
/dev/ttyA* terminal/dialin ports
/dev/cuaA* dialout ports
/dev/ttyiA* initial termios state devices
/dev/ttylA* locked termios state devices
/dev/cuaiA* initial termios state devices for dialout ports
/dev/cualA* locked termios state devices for dialout ports
SEE ALSO stty(1), sio(4), termios(4), tty(4), comcontrol(8), sicontrol(8)HISTORY
This driver is loosely based on driver code originating at Specialix, which was ported to run on BSDI by Andy Rutter <andy@specialix.co.uk>.
The System V driver source is/was available by ftp from ftp.specialix.co.uk.
This driver is not supported by Specialix International.
AUTHORS
Peter Wemm <peter@netplex.com.au> obtained the code from Andy Rutter and ported it to FreeBSD and threw the man page together. Bruce Evans
<bde@zeta.org.au> provided a large amount of assistance during porting. Nick Sayer <nick@specialix.com> wrote the EISA, PCI and SX portions.
BUGS
The interrupt tuning rate is not believed to be optimal at this time for maximum efficiency.
Polled mode (a feature of standard Specialix drivers) is not implemented, but it can be approximated by turning on machdep.si_realpoll. The
poll frequency is set by machdep.si_pollrate (in units of 1/100th of a second).
The driver does not yet support baud rates higher than 115,200 on SX modules.
Operation outside the traditional ISA "hole" is not yet supported, although it should work if the test is removed from the probe routine.
Multiple host cards are supported although combinations of hosts on different bus types have not been tested - device numbering is known to
be a problem and may lead to unexpected results.
BSD September 16, 1995 BSD