Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

snd_sb16(4) [freebsd man page]

SND_SBC(4)						   BSD Kernel Interfaces Manual 						SND_SBC(4)

NAME
snd_sbc, snd_sb16, snd_sb8 -- Creative Sound Blaster ISA and compatible bridge device driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device sound device snd_sbc device snd_sb16 device snd_sb8 Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5): snd_sbc_load="YES" snd_sb16_load="YES" snd_sb8_load="YES" Non-PnP cards require the following lines in device.hints(5): hint.sbc.0.at="isa" hint.sbc.0.port="0x220" hint.sbc.0.irq="5" hint.sbc.0.drq="1" hint.sbc.0.flags="0x15" DESCRIPTION
The snd_sbc bridge driver allows the generic audio driver sound(4) to attach to Creative Sound Blaster ISA (mostly SB16 or SB8, known as SoundBlaster Pro) compatible audio cards. The value of flags specifies the secondary DMA channel. If the secondary DMA channel is C, set the flags to (C | 0x10). For a sound card without the secondary DMA channel, the flags should be set to zero. HARDWARE
The snd_sbc driver supports the following sound cards: o Avance Asound 110 o Avance Logic ALS100+ o Avance Logic ALS120 o Creative SB16 o Creative SB32 o Creative AWE64 o Creative AWE64 Gold o Creative ViBRA16C o Creative ViBRA16X o ESS ES1681 o ESS ES1688 o ESS ES1868 o ESS ES1869 o ESS ES1878 o ESS ES1879 o ESS ES1888 DIAGNOSTICS
sb_dspwr(XX) timed out. A command to the DSP has timed out. Check the I/O port configuration. bad irq XX (5/7/9/10 valid) The IRQ given to the driver is not valid. SEE ALSO
sound(4) HISTORY
The snd_sbc device driver first appeared in FreeBSD 4.0. AUTHORS
Seigo Tanimura <tanimura@r.dl.itc.u-tokyo.ac.jp> BSD
February 17, 2007 BSD

Check Out this Related Man Page

SND_ES137X(4)						   BSD Kernel Interfaces Manual 					     SND_ES137X(4)

NAME
snd_es137x -- Ensoniq AudioPCI ES137x bridge device driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device sound device snd_es137x Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): snd_es137x_load="YES" DESCRIPTION
The snd_es137x bridge driver allows the generic audio driver sound(4) to attach to the Ensoniq 137x audio cards. Runtime Configuration The following sysctl(8) variables are available in addition to those available to all sound(4) devices: hw.snd.pcm%d.latency_timer Controls the PCI latency timer setting. Increasing this value will solve most popping and crackling issues (especially on VIA motherboards). hw.snd.pcm%d.spdif_enabled Enables S/PDIF output on the primary playback channel. This sysctl(8) variable is available only if the device is known to support S/PDIF output. dev.pcm.%d.polling Experimental polling mode, where the driver operates by querying the device state on each tick using callout(9). Polling is disabled by default. Do not enable it unless you are facing weird interrupt prob- lems or if the device cannot generate interrupts at all. HARDWARE
The snd_es137x driver supports the following sound cards: o Creative CT5880-A o Creative CT5880-C o Creative CT5880-D o Creative CT5880-E o Creative SB AudioPCI CT4730 o Ensoniq AudioPCI ES1370 o Ensoniq AudioPCI ES1371-A o Ensoniq AudioPCI ES1371-B o Ensoniq AudioPCI ES1373-A o Ensoniq AudioPCI ES1373-B o Ensoniq AudioPCI ES1373-8 SEE ALSO
sound(4) HISTORY
The snd_es137x device driver first appeared in FreeBSD 4.0. AUTHORS
Russell Cattelan <cattelan@thebarn.com> Cameron Grant <cg@FreeBSD.org> Joachim Kuebart Jonathan Noack <noackjr@alumni.rice.edu> BSD
November 29, 2006 BSD
Man Page