UDAV(4) BSD Kernel Interfaces Manual UDAV(4)NAME
udav -- Davicom DM9601 USB Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device ehci
device uhci
device ohci
device usb
device miibus
device udav
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_udav_load="YES"
HARDWARE
The udav driver supports the following adapters:
o Corega FEther USB-TXC
o ShanTou ST268 USB NIC
DESCRIPTION
The udav driver provides support for USB Ethernet adapters based on the Davicom DM9601 chipset.
For more information on configuring this device, see ifconfig(8).
SEE ALSO altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), usb(4), ifconfig(8)
Davicom DM9601 data sheet, http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf.
HISTORY
The udav device driver first appeared in NetBSD 2.0.
AUTHORS
The udav driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD July 16, 2005 BSD
Check Out this Related Man Page
UDAV(4) BSD Kernel Interfaces Manual UDAV(4)NAME
udav -- Davicom DM9601 USB Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device ehci
device uhci
device ohci
device usb
device miibus
device udav
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_udav_load="YES"
HARDWARE
The udav driver supports the following adapters:
o Corega FEther USB-TXC
o ShanTou ST268 USB NIC
DESCRIPTION
The udav driver provides support for USB Ethernet adapters based on the Davicom DM9601 chipset.
For more information on configuring this device, see ifconfig(8).
SEE ALSO altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), usb(4), ifconfig(8)
Davicom DM9601 data sheet, http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf.
HISTORY
The udav device driver first appeared in NetBSD 2.0.
AUTHORS
The udav driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD July 16, 2005 BSD
When I attach a USB storage device to my Solaris server, the mount point is coming up as /rmdisk/unnamed_rmdisk
Is there anyway I can have this device come up as a mounted device with a predetermined mount name eg /morespace rather than unnamed_rmdisk ? (0 Replies)
I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential... (0 Replies)
hi, i am on a quest to access and even mount if possible a drive on os x. there is no driver for the device, but it lists fine in the system profiler. can i access its location from the terminal? how? here is what i get on the system profiler:
Speed: Up to 480 Mb/sec
Manufacturer: SAMSUNG
... (3 Replies)
Hi
I'm looking for a simple and nice sample for writing a device driver in SCO OpenServer 5.0.7. I'm asked to write a device driver for some usb printer. I have already the linux version of the driver but it won't get compiled. I have some basic knowledge of device drivers phenomena such as kernel... (4 Replies)
I'm writing a simple USB driver to drive a stepper motor based on USB Skeleton 2.2 Driver, kernel 3.8. The basic version is running properly. As a advancement, I introduced KTHREAD to call the DEVICE_WRITE (skel_write) (), so that the driver will be available for other tasks & requests.
Calling... (0 Replies)
Hello,
I have some doubt about the NIC device on my AIX box.
When using lsdev command
/ > lsdev -Cc adapter | grep en
ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent2... (11 Replies)