smp_rep_manufacturer(8) [debian man page]

SMP_REP_MANUFACTURER(8) 					     SMP_UTILS						   SMP_REP_MANUFACTURER(8)

NAME

       smp_rep_manufacturer - invoke REPORT MANUFACTURER INFORMATION SMP function

SYNOPSIS

       smp_rep_manufacturer [--help] [--hex] [--interface=PARAMS] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Management Protocol (SMP) REPORT MANUFACTURER INFORMATION function request to a SMP target. The SMP target is identified by the
       SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE
       to identify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present.

OPTIONS

       Mandatory arguments to long options are mandatory for short options as well.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less the CRC field) in hexadecimal.

       -I, --interface=PARAMS
	      interface  specific  parameters.	In this case "interface" refers to the path through the operating system to the SMP initiator. See
	      the smp_utils man page for more information.

       -r, --raw
	      send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if  the	SMP_DEVICE
	      has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number
	      in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of the output. Can be used multiple times

       -V, --version
	      print the version string and then exit.

       -z, --zero
	      zero the Allocated Response Length field in the request. This is required for strict SAS-1.1 compliance. However this option  should
	      not be given in SAS-2 and later; if it is given an abridged response may result.

CONFORMING TO

       The  SMP  REPORT  MANUFACTURER function was introduced in SAS-1, with small additions in SAS-1.1 . This function remains unaltered in SAS-2
       and SPL-1.

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright (C) 2006-2011 Douglas Gilbert
       This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A  PARTICULAR  PUR-
       POSE.

SEE ALSO

       smp_utils, smp_discover(smp_utils)

smp_utils-0.96							     May 2011						   SMP_REP_MANUFACTURER(8)

SMP_REP_PHY_EVENT_LIST(8)					     SMP_UTILS						 SMP_REP_PHY_EVENT_LIST(8)

NAME

       smp_rep_phy_event_list - invoke REPORT PHY EVENT LIST SMP function

SYNOPSIS

       smp_rep_phy_event_list  [--help]  [--hex]  [--index=IN]	[--interface=PARAMS]  [--raw]  [--sa=SAS_ADDR]	[--verbose]  [--version]  [--zero]
       SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Management Protocol (SMP) REPORT PHY EVENT LIST function request to	a  SMP	target.  The  SMP  target  is  identified  by  the
       SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE
       to identify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present.

OPTIONS

       Mandatory arguments to long options are mandatory for short options as well.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less the CRC field) in hexadecimal.

       -i, --index=IN
	      starting phy event list descriptor index. ID is a value between 1 and 65535. Default is 1.

       -I, --interface=PARAMS
	      interface specific parameters. In this case "interface" refers to the path through the operating system to the  SMP  initiator.  See
	      the smp_utils man page for more information.

       -r, --raw
	      send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies  the  SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE
	      has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number
	      in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of the output. Can be used multiple times

       -V, --version
	      print the version string and then exit.

NOTES

       Similar information is maintained for SAS SSP target phys (e.g. on a SAS disk). It can be obtained from the Protocol Specific Port log page
       with the sg_logs utility.

       Similar information may be obtained for SAS initiator phys (e.g. on a SAS HBA). As an example in Linux  2.6.28  error  information  can	be
       found in this directory /sys/class/sas_phy/phy-4:0 (for the phy 0 in SCSI/SAS host 4).

       Similar information may be obtained for SATA device phys (e.g. on a SATA disk). If there is a SAT layer between OS and the SATA device then
       the sg_sat_phy_event utility can fetch the information.

CONFORMING TO

       The SMP REPORT PHY EVENT LIST function was introduced in SAS-2 .

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright (C) 2011 Douglas Gilbert
       This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A  PARTICULAR  PUR-
       POSE.

SEE ALSO

       smp_utils, smp_phy_control, smp_rep_phy_event(smp_utils) sg_logs, sg_sat_phy_event(sg3_utils)

smp_utils-0.96							     May 2011						 SMP_REP_PHY_EVENT_LIST(8)